Recent Activity
All
connerg461 Added a reply to 2024 Kawasaki KX450 and KX450X
2/17/2026 12:02pm Can you elaborate?
More »
connerg461 Added a reply to 2024 Kawasaki KX450 and KX450X
2/7/2026 6:03am So you removed the clutch basket gear from your 2021 KX450, installed it on a Rekluse clutch basket, and then essentially installed it on a 2024 KX450?
connerg461 Added a reply to 2024 Kawasaki KX450 and KX450X
2/6/2026 9:40pm Heys guys. I purchased a full Hinson clutch that was gently used and I was told it would fit a 24-26 kx450. The Hinson part numbers are for a 2019-2020 KX450 and I reached out to Hinson and they confirmed the Hinson components will fit in my 25 KX450. My concern is that the gear installed on the back of...
connerg461 Started a new thread 2024-2026 KX450 Hinson clutch fitment question.
2/6/2026 6:45pm Heys guys. I purchased a full Hinson clutch that was gently used and I was told it would fit a 24-26 kx450. The Hinson part numbers are for a 2019-2020 KX450 and I reached out to Hinson and they confirmed the Hinson components will fit in my 25 KX450. My concern is that the gear installed on the back of...
This forum thread has 0 replies.
connerg461 Added a reply to 2024 Kawasaki KX450 and KX450X
2/5/2026 6:44pm My 24 has 64 hours. Zero issues. I ride it pretty hard too. My 25 is new. I love both
connerg461 Added a reply to 2024 Kawasaki KX450 and KX450X
2/5/2026 6:43pm So I did a deep dive after I made my initial post and if oil gets near the slave cylinder there is a possibility for the slave cylinder to hydro lock. My plan is to pull the slave cylinder and clean any oil that may have made it past the seal when I removed the push rod. I also plan...
connerg461 Added a reply to 2024 Kawasaki KX450 and KX450X
2/5/2026 3:52pm I’m currently replacing the clutch on my 2025 KX450SR with a full Hinson clutch. During the disassembly I pulled the push rod and later read in the manual that I shouldn’t have removed the push rod because engine oil could get into the seals of the master cylinder and damage them. I reinserted the push rod with some grease on...
connerg461 Added a reply to 2024 Kawasaki KX450 and KX450X
1/26/2026 11:40am Yeah I’m just going to run it and see what happens. I change the engine oil every 2 hours and change the filter every other oil change so I’ll be monitoring the condition of the oil and if I notice anything I’ll be splitting cases. That collar did come off once I sprayed some penetrating fluid on it and I...
LouisianaMotocross Liked a reply to forum topic 2024 Kawasaki KX450 and KX450X
1/26/2026 11:23am I’m sure it would be fine. The collar wasn’t seized if it removed easily once the seal was gone. It is a major pita to get out. Takes a lot of wiggles with channel locks and patience sometimes.
This forum topic has 3215 replies.
connerg461 Started a new thread 24 KX450 counter shaft bearing
1/25/2026 9:02pm Wanted to see what some people on here thought about this. I was replacing the counter shaft seal on my 24 KX450 (64 hours). The collar ended up being seized and impossible to remove so I drilled a hole in the counter shaft seal and ran a screw into the hole so I could pull the screw and pull the...
This forum thread has 3 replies.
connerg461 Added a reply to 2024 Kawasaki KX450 and KX450X
1/25/2026 7:52pm Wanted to see what some people on here thought about this. I was replacing the counter shaft seal on my 24 KX450 (64 hours). The collar ended up being seized and impossible to remove so I drilled a hole in the counter shaft seal and ran a screw into the hole so I could pull the screw and pull the...
connerg461 Added a reply to Over tightened rear spokes
1/14/2026 1:54pm @Thisusernameisavailable I guess I wouldn’t say I’m over tightening any spokes. What I did is I laced up the wheel, torqued the spokes to 44 inch pounds, and then tightened a few spokes to make the wheel true. I’ll start over though and see try the method you suggested.
connerg461 Added a reply to Over tightened rear spokes
1/14/2026 12:27pm @dirt_trix177 did you ever run into any issues with your wheel? I just laced up a wheel with some fresh spokes and ran into pretty much the same scenario you described above.
connerg461 Added a reply to 125/150/250/300 KTM/HUS/GG jetting thread
3/21/2023 6:27pm Dude! These settings are spot on. I ended up getting the 5.5 slide. It’s such a crisp responsive bike now.