1985 Honda CR125 build (Never Two Without Three)

JMX82
Posts
1643
Joined
5/9/2013
Location
Hyllykallio, FI
10/16/2026 12:21am Edited Date/Time 10/16/2026 12:36am

Once I got the chain installed on the bike, it was time for the first test ride. The DDJ needle that was originally in the carburetor was way too rich, so I replaced it with a DGL needle, and the bike's performance improved significantly. I rode a few laps around the house and confirmed that the engine and gears seem to work just like they should. My 1984 Honda CR125, which I built previously, also made it into the photos.The bike is still missing the front brake and a few other small parts before my project is completely finished. 

IMG20260910214511
Carburetor needle kit I picked up from eBay
IMG20261003182215.jpg?VersionId=Q1SwzysL
IMG20261003182331
I need to get my third CR in the same picture but it's currently in a another garage 
8
Inferno
Posts
472
Joined
3/8/2024
Location
Laguna, IC
10/16/2026 1:15am

That CR looks awesome, and the photos with the midnight sun are beautiful!
Finland is gorgeous!

(I would make the exhaust bracket a bit thicker (4–5 mm) 😉

1
JMX82
Posts
1643
Joined
5/9/2013
Location
Hyllykallio, FI
10/16/2026 2:58am
Inferno wrote:

That CR looks awesome, and the photos with the midnight sun are beautiful!
Finland is gorgeous!

(I would make the exhaust bracket a bit thicker (4–5 mm) 😉

Thanks for the compliments! Yeah, I might design a thicker bracket later and have it CNC-machined from billet aluminum. Cutting 5 mm aluminum plate with an angle grinder wasn't exactly ideal. 😄    

1
JMX82
Posts
1643
Joined
5/9/2013
Location
Hyllykallio, FI
10/20/2026 11:54pm Edited Date/Time 1 day ago

We are almost done with this build! The aftermarket front brake I had ordered for the bike finally arrived, and I could assemble it. I also designed an HRC-style brake hose guide and got it 3D printed. I had to mount the front number plate decal from Evo-MX  first, and after that, I could assemble the front brake and bleed it, which went fairly smoothly.

IMG20261005213405.jpg?VersionId=kJu pwoGMFfInpkRaE.dOjcS1OJCHYr
Brake hose guide 0
Hose guide 3D model in Creo
IMG20260928123646 1
The 3D printed hose guide turned out pretty nice! 

IMG20261005213941.jpg?VersionId=X5iGJX8FQAVN kVIMG20261016212242 0IMG20261009220334

IMG20261019215301
6

The Shop

JMX82
Posts
1643
Joined
5/9/2013
Location
Hyllykallio, FI
1 day ago Edited Date/Time 1 day ago
The devil is in the details. I installed hose clamps to keep the fork boots in place, along with blue anodized aluminum caps for the fork air valves. I also mounted an hour meter on the bike using my go-to method, 3M Dual Lock tape. This makes swapping the meter easy if needed later on, and avoids having to drill mounting holes into the frame.
 
Earlier, I also noticed that the rear end of the Honda was sitting a bit low. Comparing the parts, I realized that the 1985 CR125 linkage pull rods were 20 mm longer, which explained the low rear stance since I'm using a 1986 main frame. I decided to source a set of 1986 pull rods to fix the issue. I quickly found a good used part from BS Parts NL, and it arrived in less than a week. After swapping in the 1986 pull rods, the bike's stance improved significantly with the rear end finally sitting at the proper height.
IMG20261104212710IMG20261117213538IMG20261117215842IMG20261111212838.jpg?VersionId=4NMYO6zuuDdHe1SQCIMG20261111213014.jpg?VersionId=YZ
IMG20261117221017.jpg?VersionId= 2
Hour meter mounted with 3M Dual Lock—no drilling required
IMG20261117221416
The hour meter sits nicely tucked between fuel tank and left side radiator
IMG20261104221228.jpg?VersionId=yJ9UOoEhb l2G
'85 linkage pull rod on the left and '86 model on the right.  
IMG20261104221404
Comparing the '85 and '86 pull rods—that 20 mm difference makes a big impact
IMG20261105221038.jpg?VersionId=iELgmQztciqOr6A1
After swapping in the 1986 pull rods, the bike's stance improved significantly with the rear end finally sitting at the proper height.
Before after.jpg?VersionId=K lK8j7FKMic15Ho7SHfN9YxY.bsjeF
The rear end looks much better with the shorter linkage pull rod.
2

Post a reply to: 1985 Honda CR125 build (Never Two Without Three)

The Latest