Added reply in a thread WTB/ISO yz125 JD jet kit 8/20/2018 3:50 PM

Thank you for the reply, let me rephrase my initial post. Is anyone selling a used or cheaper than retail JD jet kit for my bike, really only want the needles.

Started new thread WTB/ISO yz125 JD jet kit 8/20/2018 12:34 AM

I really just want the needles from a jd jetting kit, 2017 yz125. I had the needles for my 06 yz125 and remember them helping the transition into over rev. Part number from jd: JDY005

This forum thread has 3 replies

Added reply in a thread 2016 yz125 exhaust 3/5/2018 12:03 AM

PC Factory sound 304, best sounding and performing silencer on a yz125 Imo! Shorty does not rev out like the slightly longer 304 factory sound.

Added reply in a thread Husky / KTM 125 parts 2/26/2018 7:19 PM

Ignition and Manual sold! Shipping tomorrow morning.

Added reply in a thread Husky / KTM 125 parts 2/23/2018 6:15 PM

I can do $110 shipped for both, lowest. Manual was $40 ignition was $150 I think my pricing is fair.

Added reply in a thread Husky / KTM 125 parts 2/23/2018 3:46 PM

It actually allows the bike to over rev, stock ignition, at least on my Husky Tc125 was super flat on top, would not rev out like a 125 should (IMO). This had better response in the mid range and allowed over rev, best part I ever put on the bike. CD

smile
... more »
Added reply in a thread Husky / KTM 125 parts 2/23/2018 12:02 PM

Want gone!!

Started new thread Husky / KTM 125 parts 2/19/2018 8:10 PM

I recently sold my 2015 Husqvarna Tc125 and have some parts for sale! I would consider trade on some parts for some Yz125 parts. You can contact me via the phone number in my CL link or here. Have a blessed day! https://sandiego.craigslist.org/nsd/mpo/d/husqvarna-ktm-2-stroke-parts/6500746092.html

This forum thread has 7 replies

Added reply in a thread Tc125 cutting out. 8/31/2017 8:39 PM

Reeds/cage assembly cured the issue. Bike pulls hard all the way through now, no cutting out! Felt like it had full power again and no more fuel pooling up in the carb boot!

Added reply in a thread Tc125 cutting out. 8/11/2017 2:42 PM

This bike has actually been one of the longest (most kicks) 125's I have ever ridden, most started 1st or 2nd, this bike is always like 4th or 5th kick until really warm/hot. Oh yeah, that is crazy!!! Thank you for the useful information!

Added reply in a thread Tc125 cutting out. 8/11/2017 12:29 PM

Well it is a 2015 like the title states, so a completely different motor lol... I leaned the main out 3 more than what it was, from a 180 to a 172 and still the same problem, went to a 190 main, same problem, just took longer for the RPM to build with ... more »

Added reply in a thread Tc125 cutting out. 8/11/2017 12:24 AM

I have one on the way, but for a much better price

smile
! I am relieved I found the issue finally!
Added reply in a thread Tc125 cutting out. 8/10/2017 5:31 PM

Float height is spot on! FOUND THE ISSUE! Reed cage is warped, they do not seal. If you flip the reeds around on the cage they still do not seal... So I took some measurements and sure enough, the cage is warped. So I am unsure what to pursue. Neither ... more »

Added reply in a thread Tc125 cutting out. 8/10/2017 2:23 PM

I am going to get her warmed up and see what it is warm, just for funsies! I am also unaware of how accurate this compression tester is. It feels like a 125 when you kick it over... LOL. I showed my father (Mechanic of 40 years) the ignition map connectors ... more »

Added reply in a thread Tc125 cutting out. 8/9/2017 1:00 AM

Ok, compression from about 5 full kicks, throttle wide open, I got about 160 PSI, COLD, in my sneakers. I would guess that with a single-ring forged piston that is a decent reading cold (68 Fahrenheit ambient temp) with squish at 1.22mm. I went through ... more »

Added reply in a thread Tc125 cutting out. 8/8/2017 10:48 AM

Please explain your reasoning, it says to use at the least 98 octane with this KTM factory/SXS ignition. Manual says to run 40:1, should I start there?

Added reply in a thread Tc125 cutting out. 8/8/2017 9:37 AM

I am going to check them all this week, in a day or so once I have some free time! It was mainly cutting out at mid-throttle. The richer needle cured this about 80%, if not more. Right now I feel that with the richer main it pulled worse up top, so I ... more »

Added reply in a thread Tc125 cutting out. 8/7/2017 10:03 AM

You know now that you mention it I remember having one of JD's needles in my yz125 and I remember it cleaning it up a bit! We will see how it goes with testing this weekend, I should have those jets in a few days, as well as that super super special ... more »

Added reply in a thread Tc125 cutting out. 8/6/2017 9:28 PM

Joe, you can it it in this video too, and she just doesn't "scream" up top like I know she wants to or can! This video is with the first jetting, the richer needle almost alleviated that cutting out issue! But still no over-rev, did I go the wrong direction ... more »

Added reply in a thread Tc125 cutting out. 8/6/2017 9:26 PM

The 2015 has a different motor than your 2016, I am really wishing I had your motor as I have heard they are phenomenal. This one is too, just having a minor issue. I have checked the powervalves on my bike though

smile
. They are set properly and ... more »