Posts
145
Joined
2/20/2018
Location
Richland, MI, USA
Edited Date/Time
10/5/2020 7:22am
*If youre going to ask if I'll sell the whole bike, yes I will. But it will be a bundle of all the prices listed below which is around $2500.
I am looking to part out this project I started earlier this year. It was going to be a flip, but I will need the money sooner than when I will likely have it finished. Yes prices will appear high, but they’re all based off parts I’ve seen sell online plus all the extra coating and parts gone into each. If you have questions please message me. Nothing is firm.
As you can see, it has been gone through nearly 100%.
Frame - No title. Fresh flo green powder. Comes with new chain rollers and cerakoted black pegs. $200
Subframe - Powder coated gloss black $100
Swingarm- Gloss black Powder, new pivot works bearings, new Acerbis chain slider, new hardware $150
Primary Drive chain guide cerekoted bronze - $45
50 tooth Renthal rear sprocket in black. Installed but never used- $60
12 and 13 tooth front sprockets. No packaging. New - $20.
Front brake master and caliper. Stripped, blasted and cerekoted bronze. Completely rebuilt. $125
Rear brake master and caliper. Stripped, blasted and cerekoted bronze. Completely rebuilt. $125
Forks. Complete seal and bushing rebuild with Maxima fluid. $150
Renthal handlebars. Black. These are used with signs of tie downs. Has pad but no cover. I can add a black/red cover if you want. K-971 bend. New Renthal half waffle medium grip on the left. I can try pulling off the throttle tube grip and sell with the bar if you want. $60 with grips. $50 without
Wheels/tires - New Starcross 5 medium tires, new tubes, new Dubya USA spokes, new wheel bearings. Rims coated gloss black. Hubs cerekoted bronze. $600 (I have about $550 invested in parts alone. Cerkoting and assembly/trueing I did. I’m not trying to rip anyone off)
Carb - vapor honed, new choke, tusk fuel and idle screws. Including new throttle cable. If you need the throttle tube/assembly let me know. $150
Fuel tank - $50
Airbox - $50
Cylinder/head/piston - Cylinder welded and replated by Powerseal USA ($300) Head was cerekoted black. There was some detonation on the head I did a mild polish job to clean. New spark plug. Stock size vertex piston. ($114) $450
Engine cases - Vapor honed. New main bearings and seals. $200 for both sides.
Inside clutch cover - Cerkoted bronze. Comes with attached gears. $100
Transmission $100
Stator and magneto $100
Coil $20
CDI $75
Pro Circuit Pipe SOLD
Reed valve $30
Shock linkage - vapor honed and new bearings. Cerekoted arms bronze. $150
Rear Shock - SOLD
Radiators - SOLD
Please ask if you have questions and for more pictures if you want. Easy to get ahold of me via email too. Bradrussell21@gmail.com
I’d like to ship as little as possible but I’m open to shipping with shipping on top of prices.
I am looking to part out this project I started earlier this year. It was going to be a flip, but I will need the money sooner than when I will likely have it finished. Yes prices will appear high, but they’re all based off parts I’ve seen sell online plus all the extra coating and parts gone into each. If you have questions please message me. Nothing is firm.
As you can see, it has been gone through nearly 100%.
Frame - No title. Fresh flo green powder. Comes with new chain rollers and cerakoted black pegs. $200
Subframe - Powder coated gloss black $100
Swingarm- Gloss black Powder, new pivot works bearings, new Acerbis chain slider, new hardware $150
Primary Drive chain guide cerekoted bronze - $45
50 tooth Renthal rear sprocket in black. Installed but never used- $60
12 and 13 tooth front sprockets. No packaging. New - $20.
Front brake master and caliper. Stripped, blasted and cerekoted bronze. Completely rebuilt. $125
Rear brake master and caliper. Stripped, blasted and cerekoted bronze. Completely rebuilt. $125
Forks. Complete seal and bushing rebuild with Maxima fluid. $150
Renthal handlebars. Black. These are used with signs of tie downs. Has pad but no cover. I can add a black/red cover if you want. K-971 bend. New Renthal half waffle medium grip on the left. I can try pulling off the throttle tube grip and sell with the bar if you want. $60 with grips. $50 without
Wheels/tires - New Starcross 5 medium tires, new tubes, new Dubya USA spokes, new wheel bearings. Rims coated gloss black. Hubs cerekoted bronze. $600 (I have about $550 invested in parts alone. Cerkoting and assembly/trueing I did. I’m not trying to rip anyone off)
Carb - vapor honed, new choke, tusk fuel and idle screws. Including new throttle cable. If you need the throttle tube/assembly let me know. $150
Fuel tank - $50
Airbox - $50
Cylinder/head/piston - Cylinder welded and replated by Powerseal USA ($300) Head was cerekoted black. There was some detonation on the head I did a mild polish job to clean. New spark plug. Stock size vertex piston. ($114) $450
Engine cases - Vapor honed. New main bearings and seals. $200 for both sides.
Inside clutch cover - Cerkoted bronze. Comes with attached gears. $100
Transmission $100
Stator and magneto $100
Coil $20
CDI $75
Pro Circuit Pipe SOLD
Reed valve $30
Shock linkage - vapor honed and new bearings. Cerekoted arms bronze. $150
Rear Shock - SOLD
Radiators - SOLD
Please ask if you have questions and for more pictures if you want. Easy to get ahold of me via email too. Bradrussell21@gmail.com
I’d like to ship as little as possible but I’m open to shipping with shipping on top of prices.
Post a reply to: 1997 KX125 Resto Partout location Michigan