WR 250 f error code 43

adamek_jg
Hey, at the beginning I would like to apologize for my English, notwithstanding i hope that it will be possible to solve the problem.
My motocycle is Yamaha WR 250f 2017.

I have problem with engine code (43) Fuel system voltage: incorrect voltage supplied to the fuel in-jector and fuel pump.

I followed step by step with official service manual; i checked all fuses, relays and wire harness (short/open circuit) all of them is CORRECT, but error code 43 is still flashing.

Starter Relay is also fine.

The tip is, that main relay is all time working (it should not be like that), relay is all time warm and discharges the battery.

The next tip is, that the error code appeared the day after thorough cleaning.

I cleaned all plugs and corroded elements but is still the same... code 43.

I have no idea what is wrong.

Any ideas? Thanks Adam.
|
Paw Paw 271
Profile picture for user Paw Paw 271
Posts
3632
Joined
4/3/2013
Location
Benton, LA US
Paw Paw 271 3/19/2018 9:38am
3/19/2018 9:38am Edited Date/Time 3/19/2018 9:39am
Try disconnecting your battery ( both cables) and touch the positive side battery cable to ground. Must be sure both sides of the battery are disconnected. This will sometimes clear a code.
If not, then you will need to clean all electrical connections and use Dielectric grease on them.
Also check the batter load voltage as the battery may be bad.

Paw Paw
adamek_jg 3/20/2018 7:22am
3/20/2018 7:22am
I cleaned all the plugs, changed the relays, checked wire harness... still flashing error code 43
Paw Paw 271
Profile picture for user Paw Paw 271
Posts
3632
Joined
4/3/2013
Location
Benton, LA US
Paw Paw 271 3/20/2018 7:55am
3/20/2018 7:55am
Did you do the other things as suggested?

Paw Paw
adamek_jg 3/20/2018 10:11am
3/20/2018 10:11am
problem solved, the problem was in ecu

The Shop

See All »
Pigasso12 6/19/2018 3:32am
6/19/2018 3:32am
Good Morning adamek_jg,

How did you fix the ecu problem?

Did you have to buy a new one, or were you able to fix it?

Thanks... and sorry for the bad english!!!
adamek_jg 6/19/2018 4:20am
6/19/2018 4:20am
Hi Pigasso12.
Unfortunately, I had to buy a new ECU.

Pigasso12 6/19/2018 4:23am
6/19/2018 4:23am
Thanks... the same happened here!!! :/
Pablo_Rochette 10/15/2019 6:24pm
10/15/2019 6:24pm
I have the exact same issue after deep cleaning my bike (2016). Did you buy stock ECU or the GYTR ECU? I can't believe that after cleaning the bike this problem arises.
Vova
Profile picture for user Vova
Posts
2
Joined
12/18/2024
Location
Vladivostok , Primorskiy kray RU
Vova 12/18/2024 6:42pm
12/18/2024 6:42pm
adamek_jg wrote:
Hey, at the beginning I would like to apologize for my English, notwithstanding i hope that it will be possible to solve the problem. My motocycle...
Hey, at the beginning I would like to apologize for my English, notwithstanding i hope that it will be possible to solve the problem.
My motocycle is Yamaha WR 250f 2017.

I have problem with engine code (43) Fuel system voltage: incorrect voltage supplied to the fuel in-jector and fuel pump.

I followed step by step with official service manual; i checked all fuses, relays and wire harness (short/open circuit) all of them is CORRECT, but error code 43 is still flashing.

Starter Relay is also fine.

The tip is, that main relay is all time working (it should not be like that), relay is all time warm and discharges the battery.

The next tip is, that the error code appeared the day after thorough cleaning.

I cleaned all plugs and corroded elements but is still the same... code 43.

I have no idea what is wrong.

Any ideas? Thanks Adam.

 Здравствуйте! У вас ошибка 43 ! 
у вас проблема с Реле! Замените реле и проблема уйдет. Реле находиться рядом с Аккумулятором. Найти его непросто, после того как насос перестает качать, через некоторое время вы услышите щелчок! Это именно это реле 🤝

Vova
Profile picture for user Vova
Posts
2
Joined
12/18/2024
Location
Vladivostok , Primorskiy kray RU
Vova 12/18/2024 6:43pm
12/18/2024 6:43pm

Post a reply to: WR 250 f error code 43