Posts: 1269
Joined: 10/14/2017
Location: 86oh, CT USA
Going to be installing a factory connection Link. Its 2mm longer then stock. Should end up lowering the rear end just a bit. I pushed the forks up 5mm up in the clamps. I usually run around 106mm of sag. Any clue what I should set my sag to after I install the link? Should I lighten up the compression a few clicks since the initial stroke will be stiffer? Trying to get a solid baseline before I go and ride. Suspension is all stock. 190lb vet rider.
Posts: 6719
Joined: 11/30/2013
Location: Portland/Los Angeles, CA USA
Sag should be remeasured and set at what you are comfortable with. Ride it before you touch the clickers so you have a baseline with the new link compared to the old feel.
The best way is to do a moto stock then swap out the link, reset sag.
Maybe with the link you can run a higher sag number around 100-102 where i've typically ran Yamaha's.
Posts: 561
Joined: 3/2/2011
Location: CT, USA
I’ve got the link on a 2014 YZ250F, I run right around 106mm. Before it I tried prettt much everything from about 95-115, usually ended up settling right back around 105, so in all it didn’t really change my setting much.
RPM Performance
CT
783
Posts: 9103
Joined: 7/6/2015
Location: Santa Clarita, CA USA
I had my 14 yz450 done by enzo and they added a lowering plate to the shock. Recommended sag from Enzo was 100mm.
2017 RMZ450
2005 YZ250-sold :,(
1998 YZ250
2005 KX250F
80% of the time it works every time
IG @hammerfamily_4 & @2HRacing
Thanks to : Factory Effex, N2Dirt, Acerbis, DT1, Fasthouse, Matix, FMF, ASV, 100% & Mika Metals
Posts: 1269
Joined: 10/14/2017
Location: 86oh, CT USA
its the only bike ive owned that sits so high in the rear. at 5'10 its almost hard to swing my leg over.
Posts: 561
Joined: 3/2/2011
Location: CT, USA
I’m 5’8”, I feel your pain ? amazing bike but my damn stubby legs do not get along with it on concrete starts
RPM Performance
CT
783
Posts: 1269
Joined: 10/14/2017
Location: 86oh, CT USA
Posts: 561
Joined: 3/2/2011
Location: CT, USA
murph783 wrote:
I’m 5’8”, I feel your pain ? amazing bike but my damn stubby legs do not get along with it on concrete starts
fourfourone wrote:
I have short legs too it sucks.
Where in CT do you ride? Sucks that rocky hill is gone
Tell me about it. I don’t really ride much in CT anymore unfortunately-no place to go. I’ll hit up central here and there when they have an open practice. I’m usually either up at NHMX, MX23, or occasionally crow hill. Wherever is open and semi close really. You?
RPM Performance
CT
783
Posts: 1269
Joined: 10/14/2017
Location: 86oh, CT USA
Ive been trying to get in at milford riders club but there still is a huge wait list. NHMX has to be my favorite spot. I go to 23 when I don't feel like driving far.
Posts: 561
Joined: 3/2/2011
Location: CT, USA
fourfourone wrote:
Ive been trying to get in at milford riders club but there still is a huge wait list. NHMX has to be my favorite spot. I go to 23 when I don't feel like driving far.
I’ve heard Milford is a little on the small side too, I’ve never been though. We’ll have to link up and ride one of these weekends! I can’t this weekend but I’m going to try to get out as much as I can next month
RPM Performance
CT
783
