2017 KTM SXF350 with Twin Walls

55096 mikejones202 https://p.vitalmx.com/photos/users/55096/avatar/c50_whip_1608321593.jpg?1608321142 https://www.vitalmx.com/community/mikejones202,55096/all 12/03/16 1 https://www.vitalmx.com/community/mikejones202,55096/setup 16 113 4

Posts: 129

Joined: 12/3/2016

Location: Wrightsville, PA USA

11/16/2017 12:51 PM

Has anyone ran this set up and also put hand guards on? If so, where the heck did you put all on the different bar controls (map switch, kill switch, starter switch)? Right now I have them moved to the thicker part of the bar where it is 1 1/8" but the screws will not hold in place because the switches aren't meant for an area that big, so tenatively I have them held on with two zip ties.

Basically is there any better hand guards out there that make it easy with all this stuff on the bars? Thanks!

| Quote

mattyhamz2

48003 mattyhamz2 https://p.vitalmx.com/photos/users/48003/avatar/c50_8987519B_9E76_42F5_9856_056ACC0ACB29_1648443969.jpg?1648443262 https://www.vitalmx.com/community/mattyhamz2,48003/all 07/06/15 32 https://www.vitalmx.com/community/mattyhamz2,48003/setup 186 9571 102

Posts: 9766

Joined: 7/6/2015

Location: So Cal, CA USA

11/16/2017 1:30 PM

post some pictures and we can try figuring something out

| Quote

2017 RMZ450
2005 YZ250-sold :,(
1998 YZ250
2005 KX250F

Thanks to : Factory Effex, Simi Valley Cycles, N2Dirt, Acerbis, DT1, Fasthouse, Matix, FMF, Mika Metals

Moto520

37517 Moto520 https://p.vitalmx.com/photos/users/37517/avatar/c50_IMG_2336_1498787446.jpg?1498786506 https://www.vitalmx.com/community/Moto520,37517/all 02/04/13 5 89 2550 11 2

Posts: 2645

Joined: 2/4/2013

Location: Schaumburg, IL USA

11/16/2017 2:05 PM

I had to switch to the Fatbar due to lack of room for all of the controls. It is what it is. I have grown to like the fatbars over time. The flex a little more and aren't so rigid. Tough to get used to no crossbrace. I had to change and I don't even have hand guards.....just the normal mx setup.

| Quote

www.520machinery.com

Moto520

37517 Moto520 https://p.vitalmx.com/photos/users/37517/avatar/c50_IMG_2336_1498787446.jpg?1498786506 https://www.vitalmx.com/community/Moto520,37517/all 02/04/13 5 89 2550 11 2

Posts: 2645

Joined: 2/4/2013

Location: Schaumburg, IL USA

11/16/2017 2:12 PM

https://ride-engineering.com/products.php?d=1&p=c&pn=MX-KS00C-AS&t=

putting the kill switch onto the clutch lever might work.....I've never seen this and I doubt it would fit properly but it's something.

| Quote

www.520machinery.com

stone881

45421 stone881 https://p.vitalmx.com/photos/users/45421/avatar/c50_IMG_20170624_130431280_1518028131.jpg?1518027779 https://www.vitalmx.com/community/stone881,45421/all 12/26/14 9 30 668 2

Posts: 698

Joined: 12/26/2014

Location: Fruita, CO USA

11/16/2017 2:17 PM

How wicked is that bike though with the 13 tooth drive sprocket!

| Quote

Lynch

46471 Lynch https://p.vitalmx.com/photos/users/46471/avatar/c50_Arlanda_283_1426354092.jpg?1426353614 https://www.vitalmx.com/community/Lynch,46471/all 03/14/15 1 17 661 37

Posts: 678

Joined: 3/14/2015

Location: SWE

11/17/2017 1:01 AM

I ran handguards the whole season on a SXF450 without any problems? Either get the powerparts handguards (the ones you get with bike, atleast you do in EU). That eliminates any problems with lack of space, also the Zeta Stingrays worked for me however the space was limited with them on, not impossible tho. I ran Renthals 999, 996 and 997's without any real problems.