Delet

Related:
Create New Tag

7/27/2020 2:37 PM

I had some issues fitting it to the 04 so I had a spacer made I will sell with the clamps. They bolt right up to an 05 and up and you can use the same spacer if you want but bud says it’s not needed for any of the models listed as the stem mushrooms out at the top keeping the clamp from dropping down tight to the spanner nut. I did not like that so I had a spacer made to fill the gap. These are brand new have about 30 minutes at most of ride time on them no scratches at all. I would like to get 300 plus shipping. They are beautiful clamps they fit 2020 rmz plastics as well as the older rmz plastics. If you look at the pictures the top clamp has three mounting points for number plates that’s so you can fit all years. I spent a lot of time fitting these clamps and I think they work best on a 05 or newer rm125 but they work on the 04 as well and may work on an 01-03 but you would have to call bud and ask Photo
Photo
Photo

thanks

|

7/27/2020 8:18 PM

What size diameter holes for upper and lower clamps ?
Also what offset are they ?

Very nice clamps and very fair price

|

7/27/2020 8:43 PM

Offset is 23 I will have to measure the holes if you need exact measurements tomorrow. I know they are for stock rm125 forks as I ran 47mm Showas.

|

7/27/2020 10:47 PM

Are these red or brown and do they use rubber inserts between the top clamp and bar mounts?

|

7/28/2020 2:42 AM

quiknic wrote:

Are these red or brown and do they use rubber inserts between the top clamp and bar mounts?

Red and no rubber inserts if you zoom in on the top clamp you can see how there are notches for the bar mounts to sit in. These Bar mounts have a lot of adjustability.

|

7/29/2020 11:58 AM

ecmx274 wrote:

Offset is 23 I will have to measure the holes if you need exact measurements tomorrow. I know they are for stock rm125 forks as I ran 47mm Showas.

That would be great.

|

7/30/2020 4:02 PM

ecmx274 wrote:

Offset is 23 I will have to measure the holes if you need exact measurements tomorrow. I know they are for stock rm125 forks as I ran 47mm Showas.

langhammx wrote:

That would be great.

So I measured them up and came up with 54.5 on the top holes and 58.8 on the bottom holes.

|

7/31/2020 2:35 PM

ecmx274 wrote:

Offset is 23 I will have to measure the holes if you need exact measurements tomorrow. I know they are for stock rm125 forks as I ran 47mm Showas.

langhammx wrote:

That would be great.

ecmx274 wrote:

So I measured them up and came up with 54.5 on the top holes and 58.8 on the bottom holes.

If those measurements seem off please let me know my calipers may need replaced.

|

7/31/2020 4:31 PM

So I did get new calipers I have 53 top and 58 bottom

|

8/1/2020 7:28 PM

So have a set of 47mm 2012 rmz forks on a RM250 and wondering if these would work work especially stem?

|

8/1/2020 9:01 PM

Yes I was using the same forks. What year rm250?

|

8/1/2020 9:02 PM

showtimemx wrote:

So have a set of 47mm 2012 rmz forks on a RM250 and wondering if these would work work especially stem?

|

8/1/2020 9:25 PM

ecmx274 wrote:

Yes I was using the same forks. What year rm250?

2001 rm250

|

8/2/2020 5:55 AM

ecmx274 wrote:

Yes I was using the same forks. What year rm250?

showtimemx wrote:

2001 rm250

According to bud it will work. Part number is tecormrd23x which is the same from 01 to 08 for the 125 and 250. On the web site it says you will need to use a newer fender and number plate which I used the 2020 stuff and it fit great.

|