xnationalwrench's Forum Activity

Reply to YZ 250 not gettin gas. HELP! 5/4/2017 9:21 PM

You do realize that the pilot jet blockage is usually thru the center of the jet (like the main jet) NOT the side ports. And what you see is pretty much standard varnish from old gas, the carbs need a good cleaning (carb dip).

Reply to RCH Microsoft Swingarm Decal 5/4/2017 9:15 PM

Try DECAL WORKS.COM

Reply to Yz125 leaking a little gear oil at the bottom of the clutch case 5/3/2017 6:55 PM

Sounds like the water pump impeller seal is bad.

Reply to Broken Barrel 5/3/2017 7:23 AM

Any idea on how many hours on this bike? When was the top end rebuilt and were everything in spec (clearence). Did anybody port this cylinder?

Reply to YZ 250 not gettin gas. HELP! 5/2/2017 9:01 PM

Do what Paw suggests and besides checking the electrical connections and using electrical grease, also disconnect the kill button and see if that helps.

Reply to 2017 KX250F starts then dies 5/2/2017 4:31 AM

Check the fuel pump filter (in the fuel tank).

Reply to Holeshot device + air fork & traction control 5/2/2017 4:28 AM

Go to either TRANS WORLD MX or You tube video's on how to mount the device. You will need some time to see what works for you on starts.

Reply to Stankdog Outdoors 2017? 5/1/2017 10:12 AM

Verb did that series last year but they are no longer.

Reply to So I need help with an 2004 RM 125 4/30/2017 7:47 PM

You said you installed the power valve correctly but have you checked to see if they open and close while the engine is running?

Reply to 02 yz125 piston/top end 4/30/2017 7:44 PM

The piston is toast, but I would be more concerned about what shape the cylinder is in and then what clearances do you have?

Reply to Will Tomac "bunch them up" in Vegas?? 4/30/2017 4:36 PM

You do know that Dungy doesn't have to win to repeat? And considering how many KTM's and Husky's are in the class if needed they could have a tip over contest.

Reply to Breaking News: Kawasaki to release 2017.5 model with e-start this week 4/30/2017 4:27 PM

You do realize that the 18 models are pretty much done and just doing some final testing right?

Reply to Marvin's win bonus 4/30/2017 10:47 AM

There was a reason that KTM gave Marvin an extension on his contract.

Reply to Bog at low revs - Husqvarna WR 125 03 4/29/2017 2:53 PM

Sounds like you need to go smaller on the pilot jet then readjust the air screw.

Reply to Bog at low revs - Husqvarna WR 125 03 4/29/2017 6:07 AM

Has the bike been sitting very long? What kind of gas are you using? What do you have the air mixture screw set at?

Reply to Rd 16 - East Rutherford SX Links 4/28/2017 4:35 PM

You wouldn't want to be around there after dark! LOL J/K

Reply to new purchase 17 250sx break in? 4/28/2017 12:19 PM

Grease the bearings front and rear (triple clamp and rear linkage) the dealers don't do it and they are pretty light on grease from the factory and use a good quality WATERPROOF grease. Check the air filter to make sure it is oiled, check all nuts and ... more »

Reply to Are Ktm the best bikes? 4/27/2017 10:47 AM

For years and years people always wanted racers that are close as possible to "WORKS" as possible but have no idea how much work goes into maintaining and keep the bike going including buying spare parts. Unless your getting a bike for free go with what ... more »

Reply to 2016 250sxf won't start 4/27/2017 10:39 AM

Check the kill button (disconect) , then all electrical conections

Reply to Definition of "riding smooth" 4/25/2017 3:18 PM

Marty Tripes, 25 lbs. over weight, when riding Bultaco's 25% less power, and still out race most of his competitors.