Added reply in a thread Rm 125 porting 1/15/2016 5:42 PM

Did you set the squish on your bike before the head work?

Started new thread Rm 125 porting 1/15/2016 4:14 PM

Hey, I'm currently working on the motor of my 2002 rm 125, does anyone have an accurate port map of this cylinder? I'm looking to give the bike a broader power band as I will be using it for enduro! If anyone has any input here it would be appreciated ... more »

This forum thread has 6 replies

Added reply in a thread Finished (for now) Rm 125 enduro build! 1/15/2016 4:04 PM

Made a bit more progress tonight, cleaned the subframe and found a couple of repairs needed so that'll be off to my welder this weekend, while their I will also get him to fabricate a bash plate and case guards and weld mounts to the frame before powder

... more »
Added reply in a thread Finished (for now) Rm 125 enduro build! 1/14/2016 10:26 AM

I replaced all of the mentioned parts on my 08 bike and plan to do the same on this bike! I already have a dep pipe and shorty silencer for the bike and have a boyesen rad valve and moose reed spacer to try! The cylinder and head will be going to my ... more »

Added reply in a thread Finished (for now) Rm 125 enduro build! 1/13/2016 2:37 PM

Well tonight I set about trying to bring some life back to the dep pipe that came with the bike! I know these pipes work well with the bike so I decided to tackle the surface rust armed with a wire wheel and wet and dry it's been ... more »
Added reply in a thread Finished (for now) Rm 125 enduro build! 1/13/2016 6:31 AM

Just a little mod I made today to the standard rear brake lever! The standard brake tip was looking a little small and a little sorry for itself so I ground down the back of the rivets and removed it, taped out the holes with an m5 tap and bolted on

... more »
Added reply in a thread Finished (for now) Rm 125 enduro build! 1/13/2016 6:25 AM

That is one of the mods in planning, I'm also toying with trying an rmz subframe, air box and plastics! That's a good looking bike you have! Is that a standard motor or any tuning work?

Added reply in a thread Finished (for now) Rm 125 enduro build! 1/12/2016 2:30 PM

Davi millsaps

... more »
Added reply in a thread Finished (for now) Rm 125 enduro build! 1/12/2016 2:26 PM

Looks to be an older generation frame.. 01,02,03! The millsaps bike posted has the latest generation frame so maybe cancermans is one of millsaps amateur bikes?

Updated bike check psr racing's Suzuki 1/12/2016 2:08 PM
psr racing's Suzuki
Updated bike check psr racing's Suzuki 1/12/2016 2:08 PM
psr racing's Suzuki
Added reply in a thread Finished (for now) Rm 125 enduro build! 1/12/2016 2:03 PM

Added reply in a thread Finished (for now) Rm 125 enduro build! 1/12/2016 2:01 PM

That's a nice looking bike cancerman! I also have an 08 model which has a lot of work done to it! Can't get enough of these bikes! Just a shame they can't come out of the factory with a stronger gearbox! Here's my other bike which is running at a smidge ... more »

Started new thread Suzuki rm gear dogs! 1/12/2016 1:56 PM

Hey, after stripping my 02 rm 125 which I bought with a blown crank I discovered most of the dogs on all of the driven (output shaft) side gears are worn, I had the same issue on my other 08 rm 125 after only around 25 hours! I have also found some damage

... more »

This forum thread has 7 replies

Added reply in a thread Finished (for now) Rm 125 enduro build! 1/12/2016 1:45 PM

Well I managed to find a couple of hours to make some more progress on the bike tonight! It's now stripped to a bare frame apart from the rear master cylinder which has rounded off so I will have to drill that out tomorrow. Now I just need to decide

... more »
Added reply in a thread Finished (for now) Rm 125 enduro build! 1/11/2016 4:29 PM

Added reply in a thread Finished (for now) Rm 125 enduro build! 1/11/2016 4:27 PM

Started new thread Finished (for now) Rm 125 enduro build! 1/11/2016 4:25 PM

So I picked up a 2002 rm 125 tonight with the plan to strip it and rebuild it from the ground up to race enduros! I thought I'd start a thread here to show the build as it progresses and bounce a few ideas around. I bought the bike with a blown bottom

... more »

This forum thread has 70 replies

Added bike check psr racing's Suzuki 1/7/2016 2:16 PM
psr racing's Suzuki