pastmyprime214's Forum Activity

New thread Crank alignment 2/17/2020 8:32 PM

Just how easy is it to knock a crank out of alignment? Tried to knock it out with a rubber hammer before getting a right tool to push it out. Do I need to replace it or have it trued? On another note: bearing came out with the crank on the stator side. ... more »

This forum thread has 6 replies.

New thread Need a welder 2/10/2020 8:53 PM

Does anyone know someone that could fix this? Previous owners helicoil failed. Thankfully I caught this before it grenaded the motor. I’m in the southeast and the closer the better. I’m at a loss on how to fix it. Exterior of the case is fine though.

... more »

This forum thread has 2 replies.

New thread WTB: Case Splitter tool 1/25/2020 2:52 PM

I’m wanting to buy a used case splitter tool to fix the drain collar on my 08 KX250f. If anyone has the flywheel puller and clutch holder tool that would be helpful too. Can PayPal the funds.

This forum thread has 1 replies.

New thread WTB 22mm offset clamps for 08 KX250f 3/31/2019 5:40 PM

Please let me know if you have a used set of triple clamps. Not looking to pay $400 for a new set. Thanks.

This forum thread has 2 replies.

New thread 08 KX250f seat bracket 3/31/2019 5:37 PM

I went to put the seat back on after putting in the air filter and one of the seat brackets snapped off. It wasn’t at the rivot. It snapped at the bend in the metal. Any ideas where I can find a replacement?

This forum thread has 1 replies.

New thread Kx250f front brake 1/9/2018 11:07 PM

I rebuilt the master cylinder after finding a torn seal in it. Tried to bleed, only get pressure on the last half of pull and wheel didn’t spin good at all. Pulled caliper off and wheel spun great. Decided to rebuild caliper. Bleed the system and still ... more »

This forum thread has 5 replies.

New thread WTB: KX250F FORKS 9/6/2017 11:21 PM

Doing a budget build on an 08 kx250f and previous owner wrecked the forks. I need a set in fairly good condition. Can be bone stock.

This forum thread has 2 replies.

New thread Stripped frame repair 8/12/2017 12:07 AM

I had an awesome thing happen today. As I was putting the subframe on to the frame, the bolt on the shifter side completely pulled out the threads. Now I can't torque it down to spec and not sure what to do. Researched putting in a time sert but they're ... more »

This forum thread has 4 replies.

New thread Cloudy frame 4/16/2017 10:53 AM

I have a bike that I tore down and washed the frame with Shout and a red scotch brite pad. Towel dried it then I had to take care of some things. Checked it a few days later and it's very cloudy. I thought I had rinsed it all off. Where did I go wrong? ... more »

This forum thread has 2 replies.

New thread Frame mystery 4/14/2017 9:38 AM

Bought an 08 kx 250f. While tearing it down, I've seen some areas of concern. I have no clue what happened to this thing. Previous owner dumped it hard enough to break front hub. Any

... more »

This forum thread has 3 replies.

New thread Hubs for 08 kx250F 3/26/2017 7:50 AM

I need to get a new front hub for a bike I just bought. What hubs can I put on an 08 kx250F? OEM diagrams show a different part number for 07-08 and 06,09,10,11,etc. As far as I can see online, the color is the only change.

This forum thread has 3 replies.

New thread 08 KX 250F 3/23/2017 5:27 PM

So I just bought a bike from a guy who wrecked it pretty bad. Front hub and spokes are busted, forks are bound up, and plastics are coming off. However, the motor sounds stout and starts on 2nd kick. Any and all help is appreciated. Ready to bring this

... more »

This forum thread has 17 replies.

New thread A beginner...again 11/11/2016 3:04 PM

So I haven't ridden a motorcycle in about 16 years. Back when 2 strokers were the bike of choice. My buddy has 2 450 4 strokes and invited me to ride. My last bike was a 125. We just finished and I feel like I had never ridden a bike before. I was a ... more »

This forum thread has 28 replies.