pastmyprime214's Forum Activity

Reply to Crank alignment 2/21/2020 5:05 AM

Thanks guys for all the advice. I’ve emailed Ken and crank works for quotes. I’d like to ship the crank and case half to the same place. Need the drain filled and retapped too.

Reply to Case Splitter and Crank Installer Tools 1/26/2020 11:56 AM

Any chance you still have these?

Reply to WTB 22mm offset clamps for 08 KX250f 4/3/2019 9:07 PM

I’m not sure that they will.

Reply to Shift gear 36 XL 4/1/2019 8:01 PM

I’m interested in the yellow set

Reply to Kx250f front brake 1/10/2018 9:38 AM

It’s an 08. Farted around with it today and pushed the pistons in. Fluid went up into the reservoir. Pumped the lever a few times and got some of the pressure back. I’m noticing that the first half of the pull has no pressure and then it grabs. Bad line? ... more »

Reply to Kx250f front brake 1/10/2018 7:21 AM

The only thing I haven’t tried from that list is new line and banjos.

Reply to 08 KX 250F 11/10/2017 9:55 PM

Now to post the somewhat finished product. New top end, bars, graphics, chassis bearings, sprockets, all cables, and chain. eBay supplied the subframe, another set of forks, springs, axle, and shrouds. Sunk too much money into it but hell I learned a

... more »
Reply to Red Bull stream quality 10/21/2017 7:23 PM

How can some see it and others can’t. They need to freeze the racing until the server is back up

Reply to Red Bull stream quality 10/21/2017 7:15 PM

It just went dark on my iPhone. Did it happen to anyone else?

Reply to Kawasaki KX250F 07 parting out 9/6/2017 11:46 PM

I sent you a pm

Reply to Kawasaki KX250F 07 parting out 9/6/2017 11:16 PM

Still have the forks?

Reply to Pro Taper Forum Fantasy Round 10, Unadilla 8/12/2017 12:12 AM

450 1. Marvin Musquin 2. Blake Baggett 3. Eli Tomac 250 1. Aaron Plessinger 2. Zac Osbourne 3. Joey Savatgy

Reply to 08 KX 250F 4/18/2017 11:47 AM

Finally got the frame and motor clean. Slow but steady progress. I noticed a lot of carbon built up on the exhaust side of the cylinder. Is there a good way to clean this out? Also plan on doing something with the case covers. Any

... more »
Reply to Cloudy frame 4/16/2017 9:47 PM

That doesn't sound good. Hit with black magic aluminum wheel cleaner instead? Then finish it with WD40?

Reply to Frame mystery 4/14/2017 10:07 AM

So it's safe to rock on as long as the welds are good?

Reply to 08 KX 250F 4/12/2017 6:00 PM

Finally got the engine out. Pretty sure the subframe is trash now. The chassis seems straight to the naked eye. At this point I'll clean and inspect everything. Any suggestions on what I need to pay special attention to?

... more »
Reply to 08 KX 250F 4/12/2017 4:37 AM

There's a lot I don't trust on this bike in it's current state. I may take you up on those forks. New to these aluminum frames. Think it'll be ok or is that bad weak spot?

Reply to 08 KX 250F 4/10/2017 9:59 AM

Finally started the break down. Got to where I realized I didn't have an Allen key big enough to take the exhaust and swingarm off. Ran into a bit of bad news. The radiator looks as though it slammed in the frame. It made a couple dents in the radiator

... more »
Reply to 08 KX 250F 3/29/2017 3:47 PM

She got her first bath today. Amazing what a scotch brite pad and shout will do. It was obvious this thing was neglected after the crash. Ordered a used oem front hub and waiting on it to come in. Once it does, it'll be time for tear down and detail.

... more »
Reply to Hubs for 08 kx250F 3/26/2017 8:00 AM

Will I need to use the specific year rotor for that hub or are they all interchangeable?