Started new thread LL Lynns timing/results 6/17/2018 9:07 AM

Forget the old tracksideresults.com. For those who didnt know, its now ESCOREMX.COM whose doing the results and timing. IN REAL TIME. Apologies if this was already mentioned in another post.

This forum thread has 1 reply

Added reply in a thread Stankdawg in Dream Race 5/22/2018 8:15 AM

Go to Racer X. They have the whole race, plus Pingree goes down the line describing each 125

Started new thread Stankdawg in Dream Race 5/22/2018 7:28 AM

Shame he couldn't run it with having to do 2 35 minute moto's on the 250SX. Would have loved to see him in that race. You can only stretch your body so far. Plus, there was no $ to be made to help out him during the season. I'm not even sure current ... more »

This forum thread has 8 replies

Added reply in a thread YZ 125 GYTR kit? 3/31/2018 7:12 AM

I know different dynos give slightly different #'s such as Dynojet Vs Factory Dyno. 36hp doesn't seem kosher.

Added reply in a thread YZ 125 GYTR kit? 3/31/2018 7:08 AM

Do I read this right ? 36 RWHP Max ?

Started new thread Matthes and his 18 RMZ450 3/8/2018 1:32 AM

Matthes states he got himself a 2018 RMZ450 and he loves it. I for one, would LOVE TO SEE him spinning some laps on a real moto track. Anyone with a vid link for this ?

This forum thread has 69 replies

Added reply in a thread Tire mounting PSI 1/20/2018 8:02 AM

Thanks, The ISDE guys F'n amaze me... 4 minutes or so from off bike to back on. Astounding

Started new thread Tire mounting PSI 1/20/2018 6:42 AM

We all know a bit of air in the tube prevents having to start all over from the tube being pinched. I figure around 5psi is a good protecting pressure. Anyone else use more or less with good results ?

This forum thread has 9 replies

Added reply in a thread Sponsors we might not support... 1/13/2018 8:49 AM

Deal Bros, I did the SAME with BUBBA BURGERS. I even wrote them a letter saying that I saw their Logos on the KTM's. They responded with a thank you letter, discount coupons and 2 tee shirts AND, the burgers are AWESOME... A stamp and just a couple of ... more »

Added reply in a thread Time for Japan, Inc. to embrace the "affordable alternative" market niche ? 1/5/2018 6:27 PM

Rumour, and thats all I have heard. Some Pro's with no ride still go the Sushi bike route. Except for ML512 saying he "expects" Mookie to show up on a Kawi, so there must be some reason he's on Green. I guess we see 2moro night. Hoping for a fill in ... more »

Added reply in a thread De-coking 2 stroke pipe 1/5/2018 4:00 PM

Thanks Acid D, Looks like the box says Flue brush as in Chimney flue. Lowes/Home Depot, here I come

Added reply in a thread De-coking 2 stroke pipe 1/5/2018 5:55 AM

Like a plumbers snake ?

Started new thread De-coking 2 stroke pipe 1/5/2018 5:47 AM

I had decent results with Eazy Off oven cleaner in the past. The foaming action was the draw back in being able to coat the whole interior of the chamber. Shake the pipe all I wanted but just wasn't sure I was able to get the whole interior of the pipe. ... more »

This forum thread has 10 replies

Added reply in a thread Plastic rejuvenation 1/4/2018 3:05 PM

New Soft Scrub out-- Soft Scrub with OXI ! Holy S*&^%T ! INSTANT WHITE ! Areas that had rub marks did require sanding but the anything off color - yellowy tinge to it, came right back to pure white. Good Stuff BAZINGA !

Added reply in a thread Plastic rejuvenation 1/3/2018 8:49 AM

Thanks guys. I'll give those a try..

Started new thread Plastic rejuvenation 1/3/2018 7:18 AM

I've seen Joe Abbate's work on restoring the sheen to well used plastic fuel tanks and they sure look good. And the old trick of applying heat to the white crease in fenders to get the color back. Anyone have any tricks to get white back into rad louvers/fork ... more »

This forum thread has 17 replies

Added reply in a thread Cleaning Hubs and swing arm 12/30/2017 5:21 AM

I like that notion. Especially as it is listed for "rough cast alloy". Thanks, I'll give that a shot. I was going to media blast the cases, but I'll try this on those as well as see if I can save my myself from being bombarded with media.

Added reply in a thread Cleaning Hubs and swing arm 12/30/2017 5:10 AM

failed to mention, I'm leery of Muriatic acid to do the the job as I only really use that to get melted piston off of nikasil cylinders.

Started new thread Cleaning Hubs and swing arm 12/30/2017 5:07 AM

I do not intend of "de spokeing" the wheels to clean the hubs to bring back the oem look or close to it. The swing arm is stripped and needs a good cleaning as well. Anyone have an idea of a spray type of cleaner to help restore the original look rather ... more »

This forum thread has 7 replies

Added reply in a thread Extrude Hone 12/23/2017 2:09 PM

The 2nd link is a subsidiary of Link #1 which shows me that they are a BIG TIME PLAYER now. Quote from main link showing the Aerospace Industry "You make it. Extrude Hone® makes it high performance. AFM, ECM, PECM AND TEM EXTRUDE HONE® PROCESSES.". The ... more »