Added reply in a thread Who fantasizes about riding a golf course? 1/7/2019 8:34 AM

Full Gas Sprint Enduros race on a golf course in WV. https://www.youtube.com/watch?v=mr34xB29nnM

Added reply in a thread 2017 TE 250 1/7/2019 5:09 AM

So over the weekend I finally got around to installing the TC CDI box on the bike. After adjusting the jetting, I took it out for a spin. All I can say is, WOW! It made a huge difference. The track that I rode it on was sloppy muddy, the bike was too ... more »

Added reply in a thread 2017 TE 250 12/31/2018 5:21 AM

So I took the bike out for a spin yesterday. Just the TC head made a huge difference, a lot more snap. I need to mess with the jetting some, but I am going to wait until I install the TC cdi box. Even in the mud the bike felt so much faster. I can't

... more »
Added reply in a thread 2017 TE 250 12/27/2018 10:48 AM

I like them a lot in the tight technical stuff, but they bottom really hard on big hits. I think I'm going to have my local suspension guy do some work on them. They work way better than the 4cs forks that were on my 125.

Started new thread 2017 TE 250 12/27/2018 4:54 AM

So a few months back I purchased a hold over 2017 TE 250 Husky, I ended up getting a pretty good deal on it at right at $8000 out the door. https://www.vitalmx.com/forums/Moto-Related,20/With-the-approval-of-my-wife-my-wallet-decided-to-speak,1345024

... more »

This forum thread has 21 replies

Added reply in a thread 2012 xc 150 12/11/2018 12:02 PM

I had one, it was a great bike. Sold it and got a 250f. Worst mistake I ever made, at least when it comes to bikes.

Added reply in a thread Yamaha 250X or KTM250XC 12/11/2018 5:56 AM

The pipe made it rev longer, especially the silencer. I had a little issue with the fitment, I had to cut the stinger on the silencer. It was too long and would not allow the bolt holes to line up, I had to shorten it by about 1/4".

Added reply in a thread Yamaha 250X or KTM250XC 12/11/2018 5:52 AM

Mxteach stated that he would be riding mostly woods with some moto, why not go ahead an get a bike with lights, and at least in my state, can be tagged? This bike was the same price as the XC 250 at my dealer, so in my opinion it was a no brainier. I ... more »

Added reply in a thread Yamaha 250X or KTM250XC 12/10/2018 1:51 PM

I have a 2017 TE 250 Husqvarna (pretty much the same at the KTM) and I love it. All the pluses that the guys above mention and I haven't had any trouble with it. I plan on putting a TC head and CDI on it this winter. I have a PC exhaust and VForce reeds,

... more »
Started new thread 125 KTM Exhaust 12/10/2018 7:41 AM

I have a 2003 KTM 125 and I would like to put a different exhaust on it. I can find plated pipes but I would like to go with an unplated pipe. I have had a couple new 125/200 KTM's and the pipe mounting locations look the same (2004 SX 200 and 2012 XC

... more »

This forum thread has 1 reply

Started new thread 1983 Husqvarna Pro Circuit Question 12/6/2018 9:55 AM

So I have a 1983 WR 250 Husqvarna that I restored a few years ago. I race a few vintage races a year on it. I am wondering if anyone has any good pictures of the 1983 Pro Circuit bikes. I would like to build the bike into somewhat of a replica, except

... more »

This forum thread has 6 replies

Added reply in a thread SX 125 Factory Replica 11/27/2018 4:48 AM

It was an option, my car was originally a 4 wheel disk car but it now has brakes off a 1998-2002 Camaro. They are 1" bigger with much better calipers.

Added reply in a thread SX 125 Factory Replica 11/26/2018 8:33 AM

I made a skid plate for the bike over the weekend. I had a P3 Motoflex skid plate for a 2016 TC 125 laying around, I decided to give it a shot on making it fit. I trimmed the outer pieces to make it more of a glide plate instead of a skid plate. I then

... more »
Added reply in a thread SX 125 Factory Replica 11/12/2018 7:10 AM

Over the weekend I finished putting the bike back together. It still needs a couple small things, new exhaust hangers, rear tire, things like that. I plan on keep adding things to the bike over time, carbon frame guards, vForce reeds, SXS suspension,

... more »
Added reply in a thread SX 125 Factory Replica 11/8/2018 9:44 AM

A little sneak peek of the graphics for the bike. Install the graphics and clean up the exhaust and it will be done. At least for now. I can't decided if I want to make it a Hughes replica with his name and number or put my name and number on it. I have

... more »
Added reply in a thread SX 125 Factory Replica 11/5/2018 5:03 AM

I made some progress on the bike over the weekend. I ordered an exhaust, and graphics will be here Wednesday or Thursday. I'm more excited about this build than any of my others.

... more »
Added reply in a thread SX 125 Factory Replica 11/2/2018 5:26 AM

I saw a couple sets on ebay for around that price. Right now the goal is to get the bike looking good and running good. after that I'll go through and upgrade the suspension. I stripped the coating off the stock forks and they turned out pretty good.

... more »
Added reply in a thread SX 125 Factory Replica 11/1/2018 6:41 AM

So I did a little bit more to the bike last night. New seat cover and handlebars. I will be stripping the bike down to the frame this weekend, and sending the frame off to be powder coated. The bike looks 100% better already.

I am ... more »
Added reply in a thread 1987 KX 125 10/31/2018 12:29 PM

I haven't had to much trouble finding parts for it. It's much easier to find parts for than the KTM's I've been working on. I know there seems to be some pieces that are one year only parts (cylinder, exhaust, etc...) but there are a lot of parts that ... more »

Added reply in a thread SX 125 Factory Replica 10/31/2018 11:09 AM

There is currently a set of forks and shock for a 2002 SXS 125 on eBay right now. I totally thought about buying them but I can't bring myself to spend the money right now. If I could only sell my KX125.