jpatz319's Forum Activity

New thread $20,000 Pro Shootout Race in NC 10/18/2021 8:10 AM

All, One of the best tracks in NC is having a $20,000 pro shootout on Halloween weekend. They are having two pro classes - Open A and Open 2-stroke A. It should be a good time. The track is a national-caliber track that should produce some amazing racing.

... more »

This forum thread has 1 replies.

New thread WTB - Renthal FatBar 839 7/22/2021 1:31 PM

I'm looking for a set of Renthal Fatbar 839's. They are the stock bend on '19+ CRF450R and '21+KX450.

This forum thread has 1 replies.

New thread Cerakote on a airbox 1/26/2021 12:58 PM

thinking about cerakoting my airbox black on KX450. Has anyone done this and if so how well did it hold up?

This forum thread has 26 replies.

New thread 2017 KTM 250sx 10/16/2020 10:52 AM

2017 kTM 250 sx second owner 87.3 hrs full motor rebuild at 65 hrs with OEM parts (crank, bearings, seals, gaskets) and cylinder replated Wiseco top end at 20 hrs after rebuild Bike always ran on 50/50 c12 and 93 MX-Tech Lucky Carbon Spring Conversion

... more »

This forum thread has 4 replies.

New thread Track Generators 7/22/2020 12:46 PM

Looking into getting a generator to run a fan or two at the track to make life less miserable in the summer heat. I am looking at the Yamaha 2000w but what are people's experiences with the H.F. Predator or the WEN ones?

This forum thread has 19 replies.

New thread New Fox V3 Helmet 7/12/2019 1:11 PM

What are everyone's thoughts on the new Fox V3 helmet? I am in the market for a new lid and wanted to hear some real world feedback. My past helmets have been Arai's and Shoei's but I would like something with the newer rotational technology in it.

This forum thread has 14 replies.

New thread 2017 KTM Shift Fork Identification 5/1/2019 5:23 AM

I am trying to figure out what shift fork is what part number. The forks have no parts numbers on them but they do have letters on them. one has a U and the other has a W. The two part numbers are 79234003000 and 79234002000.

... more »

This forum thread has 1 replies.

New thread Mikuni TMX 38 - Needle Jet 2/3/2019 3:41 PM

I’m re-jetting my 2017 KTM 250 and I cannot for the life of me figure out how to get the needle jet out. Is there a trick to it?

This forum thread has 3 replies.

New thread 2017 Husqvarna Bar Bend 2/2/2018 7:10 AM

Im looking to replace the stock bars with a set with a crossbar. I like the bend the bike came with but I can't seem to find any dimensions on them. Does anyone know what they are so I can compare them to other bars.

This forum thread has 4 replies.

New thread 2017 Husqvarna FC350 Piston 11/7/2017 8:45 AM

I am looking at putting a top end in my bike this and looked up the cost of a replacement OEM piston is ~$400. Is the OEM piston kit worth it or should I look at something like a Wiseco. I have about 30 hours of hard mx on the bike.

This forum thread has 18 replies.

New thread 2001 CR125 wheels 9/18/2017 6:59 AM

Im looking for some new hubs for my GF's bike. I saw that tusk has a front hub but doesnt have a rear hub. Are there any other years that have a rear hub that would fit the 2001. Thanks.

This forum thread has 1 replies.

New thread AER Fork Chatter 3/7/2017 1:15 PM

I recently have gotten a FC350. I like everything about the bike but the forks in the acceleration/braking bumps. The front end seems all over the place. I have the pressure around 142psi, 15 out on compression and 15 out on rebound. I'm a 185lbs in ... more »

This forum thread has 10 replies.

New thread 2011 Yamaha YZ 250 8/9/2016 6:44 AM

2011 YZ 250 - $4150 obo Just rebuilt. 0 hours on top end and 8 hours on rebuilt bottom end. Always ran with VPC12 with Maxima K2 premix. Redline super lightweight gear ran. -Forged Wiseco piston -Balanced crank -New crank and transmission bearings -Port,

... more »

This forum thread has 0 replies.

New thread 2011 Yamaha YZ 250 5/16/2016 12:00 PM

2011 Yamaha YZ 250 $4250 obo Fresh top end with a rebuilt bottom end. Plastics conversion kit and wheels put on when the bike was rebuilt. Great bike. Engine -New Wiseco forged pistion -Cut head -ported and polished cylinder -cylinder matched to cases

... more »

This forum thread has 2 replies.

New thread Yz aluminum frame swap 6/11/2015 3:45 PM

I got a good deal on a steel frame yz144. I also have a 08 yz250 with a shift shaft thrown through the cases. I was wondering if it is possible to swap the 144 motor into the 250 frame and suspension.

This forum thread has 7 replies.