jbrass715's Forum Activity

Reply to Will a 2003 Honda cr250 fmf factory fatty fit an 02? 1/20/2021 12:50 PM

Yes it will fit, 02-04 will work

Reply to Wanted! Xr100 crf100 cases, motor, bottom end, etc 12/21/2020 1:11 PM

What condition? i have a complete bottom end

Reply to What to use for replacement intake boot 2002 cr250 11/17/2020 1:56 PM

I had a couple of them that I put the 07 boot on with TMX stock carbs on them.

Reply to Pro Circuit Pull Rods Honda-CRF 450R-17-18 part #HPA17450 11/12/2020 8:45 AM

$100 shipped?

Reply to Pro Circuit Pull Rods Honda-CRF 450R-17-18 part #HPA17450 11/11/2020 7:33 AM

Still have?

Reply to VERY low hour Stacyc E16 1/24/2020 9:37 AM

Available?

Reply to WTB: 17+ CRF450R Oem seat cover 12/20/2019 9:01 AM

I have one. Text me 417-two93-5twotwo3

Reply to Cr250 carb 11/27/2019 1:45 PM

I bet it would work. Because I put a 07 air boot on my 02 bike with stock carb. just my 2 cents

Reply to 06 cr 250 engine in 03 frame?? 9/16/2019 9:16 AM

Will fit, need 06 expansion chamber

Reply to What to use for replacement intake boot 2002 cr250 9/9/2019 12:47 PM

07 boot works fine on the 02s and is supposed to have a little better flow

Reply to 1999 Honda CR500R 8/20/2019 8:56 AM

Sold

Reply to 1999 Honda CR500R 8/8/2019 7:46 AM

Motivated seller, found the bike I need. $3,800 obo

Reply to WTB 1986-87 Honda CR250, CR500 8/7/2019 12:54 PM

Will send you some pictures tonight

Reply to 1999 Honda CR500R 8/6/2019 2:28 PM

Thanks, I have an AF swap 500 and then I rode my buddies 450. I shouldn't have rode his 450 lol

New thread 1999 Honda CR500R 8/6/2019 9:22 AM

1999 Honda CR500R for sale or trade. $4000 or would trade for a 17+ CRF450 plus some cash on my end. This bike runs great, has a ported engine, msv exhaust flange, rad valve. Has a set of 05 Crf450 forks swapped on the front end. Has been sprung for

... more »

This forum thread has 5 replies.

Reply to WTB 1986-87 Honda CR250, CR500 8/6/2019 9:11 AM

I have a 500 roller if you would like on for extra parts. 87 I believe, excel wheels, tank, shrouds, and exhaust is there

Reply to 2005 KX250 Parts 7/11/2019 10:15 AM

Picture of wheels?

Reply to 2003 CR250r DIR (Phase 2 in progress) 5/31/2019 2:31 PM

Are you using the OE expansion chamber? Or are you selling it?

Reply to WTB: Fully restored/built 2 stroke anywhere in usa 5/31/2019 1:07 PM

Werner has a nice rm250 posted on here with A kit suspension

Reply to Cr500 in an aluminum frame 5/23/2019 6:47 AM

Thanks. The pipe was built by LED Performance. I've thought about selling it,just hate to ding it up riding MX