jamiechapman418's Forum Activity

Reply to CRF250 problem 11/29/2021 1:37 PM

I just am working on one of these myself. Take some Prussian blue and check the contact patch of the valve to the seat. My valve clearances were all good but the seats were worn and leaking. Get old seats cut or I got a new head from cylinder works for ... more »

Reply to KDX 200 Carb Help 11/23/2021 12:34 PM

Have you tried a new float? Or is the float on the PWK33 the same and could try that?

Reply to CRF250R 2006-2009 Carbon parts brand new 11/22/2021 3:50 PM

Pm sent!

Reply to 2018 YZ450F Died and won’t start help!!! 11/21/2021 5:49 AM

Have your tried bump starting?

Reply to Insane MXA Gas Gas 125 video 11/20/2021 10:39 AM

Never fails. Every time I watch a video like this it makes me think I need a 125. Then I get one and realize I suck on a 125.

Reply to 2006 crf250r repair ideas needed! 11/19/2021 11:44 AM

10-4. The projects I pick up are almost always at the "Part Out" stage ha. This was actually a customers bike that I put a crank kit, piston kit, and clutch in like three years ago. Lost spark about a month ago and he called me and asked if I wanted

wink
... more »
Reply to 2006 crf250r repair ideas needed! 11/18/2021 6:23 PM

Yup that’s what I’m on now. Seats are worn past service limit. Time for some head work!

Reply to 2006 crf250r repair ideas needed! 11/14/2021 6:39 PM

Update: I replaced the new eBay stator with a used eBay oem stator and a used oem flywheel. Bike now runs. Not sure if it was stator or flywheel but whatever it was it worked! Thanks for the advice.

Reply to 1991 RM125 11/14/2021 11:55 AM

Would you consider selling the new fmf pipe?

Reply to Suzuki rmz250 2009! 11/12/2021 11:16 AM

At least I think there is

laughing
Reply to Suzuki rmz250 2009! 11/12/2021 11:15 AM

There is a vent with a tube on the backside of the valve cover.

Reply to Suzuki rmz250 2009! 11/12/2021 9:40 AM

Remove and clean, then if looks ok, reinstall with black oil resistant permatex. Torque valve cover bolts to spec.

Reply to Who makes a hinged holeshot device? 11/10/2021 1:46 PM

Pro Taper SELA is hinged

Reply to Rm125 1994 Front fork.. 11/10/2021 6:47 AM

Spring out. Fork fully collapsed.

Reply to Rm125 1994 Front fork.. 11/10/2021 6:24 AM

You need the fork oil level tool. The mm you will set on the tool and suck with the syringe. Once you stop pulling fluid and start pulling air your are at the correct level.

Reply to 2006 crf250r repair ideas needed! 11/8/2021 8:29 AM

I did not. It really does look like new though. No corrosion, scuffs, or worn spots. Maybe I should think about changing it too though.

Reply to 2006 crf250r repair ideas needed! 11/8/2021 6:07 AM

Yup did that. Woodruff key still intact, added a little lube to the shaft and put back on to torque. Thought maybe it wasn't slid on far enough.

Reply to 2006 crf250r repair ideas needed! 11/8/2021 6:05 AM

Cheapo aftermarket stator. The stator is what I replaced that made it go from zero spark, to spark only once. I will look for a known good oem and try that next.

Reply to Suzuki rmz250 help! 11/8/2021 6:03 AM

Part numbers for the 2005 and the 2009 rmz250 clutch cover are different. I believe the check bolt is located near the rear brake pedal bolt on the inner clutch cover. Should have a copper crush washer on it to help identify. Otherwise, drain oil and ... more »

Reply to 2006 crf250r repair ideas needed! 11/7/2021 4:44 PM

Spark is my issue. It does one spark, at the end of the kick stroke and that’s it. I’m not worried about a leak down or any further into engine until I can get spark. I have checked, checked, and checked timing. replaced coil, stator, spark plug, and ... more »