Added reply in a thread 04 rm125 rebuild 7/29/2020 6:33 PM

Had Racetech respiring/revalve the forks for me. They also hard anodized the uppers bronze. I put new yellow polisport fork guards and if you look closely some bling with ss as3 black fork lug bolts and a zeta brake line guide.

Added reply in a thread 04 rm125 rebuild 7/29/2020 6:23 PM

Thank you

Added reply in a thread 04 rm125 rebuild 7/29/2020 3:20 PM

I decided to go with Tom Morgan’s recommendations so I ordered up red line oil and the dumonde tech break in oil. Every bike needs a hour meter so i went with a prox as I have had good luck with them on my other bikes.

Added reply in a thread 04 rm125 rebuild 7/29/2020 3:12 PM

I got a surprise when I took the chain slider off so I sent the swingarm to motowhips to be welded. I wanted to have it polished and anodized but with it having a repair I was worried the color would vary to much so I had them powder coat it. It turned

... more »
Added reply in a thread 04 rm125 rebuild 7/29/2020 1:17 PM

Graphics by skda

Added reply in a thread 04 rm125 rebuild 7/29/2020 5:16 AM

The first time I built this bike i only did the motor and graphics. This time I want everything new or at least modified in some way. It had a 134 egr kit in it and I took that off purchased a new 05 cylinder and sent it to Tom Morgan for porting and

... more »
Added reply in a thread 04 rm125 rebuild 7/29/2020 3:52 AM

Some carbon

Added reply in a thread 04 rm125 rebuild 7/29/2020 3:50 AM

I had both calipers cerakoted burnt bronze and the hangers black. The sight glass on both master cylinders were deleted then cerakoted burnt bronze. I actually found both power valve covers on eBay already coated the same color.

... more »
Added reply in a thread 04 rm125 rebuild 7/29/2020 3:27 AM

Anodized Kashima

Started new thread 04 rm125 rebuild 7/29/2020 3:21 AM

Framed and powder coated black.

This forum thread has 68 replies

Added reply in a thread STS Shop Build - '05 RM125 (Completed Pics) 7/28/2020 5:08 PM

I have tried hard to get those clamps kite won’t sell them directly to me since I’m in the USA you wouldn’t happen to know where I can get some?

Added reply in a thread Delet 7/28/2020 2:42 AM

Red and no rubber inserts if you zoom in on the top clamp you can see how there are notches for the bar mounts to sit in. These Bar mounts have a lot of adjustability.

Added reply in a thread Delet 7/27/2020 8:43 PM

Offset is 23 I will have to measure the holes if you need exact measurements tomorrow. I know they are for stock rm125 forks as I ran 47mm Showas.

Started new thread Delet 7/27/2020 2:37 PM

I had some issues fitting it to the 04 so I had a spacer made I will sell with the clamps. They bolt right up to an 05 and up and you can use the same spacer if you want but bud says it’s not needed for any of the models listed as the stem mushrooms

... more »

This forum thread has 14 replies

Started new thread Is it safe to clean clutch plates? 7/23/2020 7:27 PM

I was soaking my clutch plates in oil and when I went to pour the oil out they slipped out and fell into old oil. Is it safe to clean them off?

This forum thread has 2 replies

Started new thread Mx mechanic lingo? 7/15/2020 1:31 PM

Might be a dumb question but what does it mean when a company says they will blueprint your transmission? I am looking for a company to polish my transmission on a 125 and one of the companies I’m looking at is tzr. Their website says they can polish ... more »

This forum thread has 4 replies

Started new thread ISO 2004 rm125 crankcase 7/13/2020 4:49 AM

As the title says I’m looking for a crankcase. I need both center and stator side cases. I will consider a complete bottom end of an 04 to 06 as well. Thanks

This forum thread has 1 reply

Added reply in a thread Cylinder studs ok to heli coil? 7/10/2020 9:57 PM

Thanks I always thought they were the same but after your post read up on them.

Started new thread Cylinder studs ok to heli coil? 7/10/2020 8:04 PM

Is it ok to heli coil one of the studs that holds my cylinder on? New case is discontinued and can’t find a used one available at the moment.

This forum thread has 8 replies

Added reply in a thread 2004 RM “Corona” build - updated 11/1 7/8/2020 3:30 PM

Looks great! So did the prox crank fit good? Did you get a chance to compare it to the 05 oem crank? Are you able to get your seat to lock into the seat button with that tank? I had to raise mine to get it to work. I also was only able to get the tank ... more »