chillrich's Forum Activity

New thread Raceday Live Steam 1/19/2019 2:59 PM

What a $hitshow! Terrible stream. Anybody else? I've emailed & tweeted RSL, SXlive and Viewlift. Hopefully they get it fixed for tonight.

This forum thread has 27 replies.

New thread Barnett Clutch 5/22/2018 11:20 PM

Looking for opinions and experience on the Barnett clutch components, specifically the basket and pressure plate. Application would be YZ125/144. I like the idea of the stainless steel plates over the basket fingers.

This forum thread has 2 replies.

New thread YZ144 JETTING 3/25/2018 12:13 PM

Hey guys, I've installed a Athena 144 kit on my 2014 YZ125 and am struggling with jetting. My jetting skills suck but I'm willing to learn. 1st issue is pilot, I warm up the bike and raise idle a bit with set screw then back out pilot until rpm peaks, ... more »

This forum thread has 5 replies.

New thread SoloSX Commentator Announcer 2/15/2018 8:12 PM

I don't follow wrestling like Weege but this guy is really good! Question is could he keep it up for a whole evening? Maybe if he toned it down a bit and had a color commentator like say Jim Holley they could do an internet stream... SX Announcer

This forum thread has 4 replies.

New thread Eccentric Crank Pin 12/18/2017 8:09 PM

I would like to find one of these to make a stroker YZ125 It appears that there is enough clearance to spin the bearing on. Apparently no case mod required. Would the pin have to be TIG welded after to prevent spinning? With a 2mm stroke the cylinder

... more »

This forum thread has 4 replies.

New thread MEC/SX Viewing Canada 10/14/2017 9:21 AM

Any new ways to view these events in the great white north or will it be the same shitshow as years past? Can only buy the pkg outside US and Canada. Fox Sports programming is available to about 12 people in eastern Canuckia.

This forum thread has 4 replies.

New thread YZ125 Noise 11/20/2016 3:40 PM

Hey Guys, I just rebuilt 2006 YZ125 engine, crank was loose and shift stopper had mostly gone through the gearbox. Replaced; All bearings engine and transmission except the water pump bearing and clutch needle bearing. Crank and top end. Entire drive ... more »

This forum thread has 3 replies.

New thread Crankshaft Press Rating 6/26/2015 5:58 AM

Would a 10T press work for 85cc crankshaft rebuild?

This forum thread has 7 replies.

New thread MXGP Xbox 360 12/31/2014 10:07 AM

Any suggestions for a good controller? Wii controller was excellent for MXvsATV back in the day.

This forum thread has 4 replies.

New thread Pourcel, Knee hit GPA? 7/20/2014 4:39 PM

After first moto Milville, Pourcel said his knee hit his GPE? what is this? Mapping or suspension?

This forum thread has 2 replies.

New thread FOx Podium RC2 Rebuild 5/24/2014 5:05 PM

Anyone have experience with rebuild of these? Are special tools required? Is this a bladder or resevoir piston?

This forum thread has 1 replies.

New thread KTM 85SX No Response From RaceTech 2/24/2014 6:57 PM

There are 2 choices for Gold Valve on the fork of the KTM 85SX, the FMGV2820 and the FMGV2820G, I've emailed Racetech 3 times now asking for clarification on the differences but haven't gotten a response. Any of you guys know what are the differences ... more »

This forum thread has 10 replies.

New thread Anybody Had a Bad Experience with Powersports Superstore???? 12/4/2013 5:33 PM

Having some issues with customer service.... anyone else?

This forum thread has 0 replies.

New thread Hangtown Torrent or Feed 5/18/2013 5:22 PM

Well, The Score network in Canuckland preempted MX for some stick and ball $hit. Anyone know of torrents or a place we can view online?

This forum thread has 6 replies.

New thread KTM 65SX 85SX Shock Service 3/4/2013 6:35 PM

I am looking for info to rebuild WP shocks BAVP3614 and PDS4618(?), in particular, separator piston height. Do these follow similar procedure to PDS5018?

This forum thread has 4 replies.

New thread The Moto: Our Future 1/10/2013 4:39 PM

The Moto: Our Future Is this an old episode? Anyone have external links? Can't get this web content in the Great White N.

This forum thread has 1 replies.

New thread KTM or Yamaha Part???? 11/17/2012 4:05 PM

I have recently worked on our 2004 KTM 65SX and 2009 YZ250F clutches, all seemed to go OK but I found this cleaning up today. Anybody seen one of these before? Checked the fiches and can't find a match.

This forum thread has 6 replies.

New thread Riding. Canadian Thanksgiving Weekend 10/8/2012 1:50 PM

I thought Dr. Sweden's thread on riding in Sweden was cool and informative so I took a few pics and dug up a few others of our riding experiences. Here goes! Riding in Regina, SK Canada, Oct 7/12

Time to get loaded up, bikes service but not ... more »

This forum thread has 12 replies.

New thread Colorad0 @rchives 6/3/2012 7:46 PM

Anybody know of any archives online

This forum thread has 3 replies.

New thread Freestone Archive 5/27/2012 12:06 PM

We were racing this weekend, when and where will these be posted online?

This forum thread has 23 replies.