Added reply in a thread Intense Tazer MX inspired E-bike 9/11/2020 2:52 PM

I can't find the MX version on their website. Only released in US?

Added reply in a thread Xtrig Rocs and Xtrig PHDS on SXF450 2019-21 = 10mm higher bar? 8/18/2020 8:36 AM

I will place an order on these today. Im interested in testing the triple clamp as well. Are they stiffer than the KTM factory clamps that i have now? Feeling of Xtrig Rocs was, lets just say, not satisfactory.

Added reply in a thread Xtrig Rocs and Xtrig PHDS on SXF450 2019-21 = 10mm higher bar? 8/11/2020 12:04 PM

So if I use the xtrig flexfix which is -5mm than phds I should get OEM height, if the PHDS adds 3mm (per info from xtrig), and the other 2mm comes from clamp itself, + 2.5mm washer added under clamp (basically 2+2.5 minus 5). Freaking lot of work for ... more »

Added reply in a thread Xtrig Rocs and Xtrig PHDS on SXF450 2019-21 = 10mm higher bar? 8/11/2020 12:00 PM

Took some measurements today. Measured from the point that goes against frame on below clamp, to in line with under the bar. Used a thin knife blade of 1mm to get exact level measurement against the bar. Overall height is 235mm (or 234 but blade is ~1mm)

... more »
Added reply in a thread Xtrig Rocs and Xtrig PHDS on SXF450 2019-21 = 10mm higher bar? 8/11/2020 11:56 AM

Yes, but I'm not sure they have even thought about the height it adds. It is used to seal toward frame but also to avoid top bolt to bottom towards axle. If I use a small oring instead and use the spacer under the main nut above the top triple clamp ... more »

Added reply in a thread Xtrig Rocs and Xtrig PHDS on SXF450 2019-21 = 10mm higher bar? 8/11/2020 3:20 AM

You happen to know if Xtrig include the 2.5mm spacer (that they say you should put under the top clamp instead of OEM oring), in getting the same Height/measurement as OEM clamp?

Added reply in a thread Xtrig Rocs and Xtrig PHDS on SXF450 2019-21 = 10mm higher bar? 8/10/2020 3:39 PM

Ok, KTM/Husky said they lowered the bar position 5mm for the 2018.5/2019 modells, so that need to come from frame adjustment/lowering then I assume. The flexfix from xtrig is 5mm lower than phds. Wonder where that number comes from. If it is like you ... more »

Added reply in a thread Xtrig Rocs and Xtrig PHDS on SXF450 2019-21 = 10mm higher bar? 8/10/2020 3:20 PM

Also since I know you are very knowledgeable within this area, a 2016 or 17 triple clamp for KTM, would they mean 5mm higher bar position automatically when mounted on a 2019+ chassi? Just feel like there was no way just 2.5+3mm was all it was taller ... more »

Added reply in a thread Xtrig Rocs and Xtrig PHDS on SXF450 2019-21 = 10mm higher bar? 8/10/2020 3:16 PM

Absolutely an option. But would like to get the handlebars moved slightly fwd which the xtrig allows me to do, OEM moves to much. Have you done any vibration reduction testing between these and phds? What I liked about the phds was that they took away ... more »

Added reply in a thread Xtrig Rocs and Xtrig PHDS on SXF450 2019-21 = 10mm higher bar? 8/10/2020 8:30 AM

Yes that im aware of. PHDS they say is 3mm higher. Then you need to add the washer of 2.5mm (Stock clamp uses oring that adds 0 mm to height). That is 5.5mm difference I will measure my stuff tonight or tomorrow, but the handlebar is another 5mm lower ... more »

Added reply in a thread Xtrig Rocs and Xtrig PHDS on SXF450 2019-21 = 10mm higher bar? 8/10/2020 7:22 AM

I have found one bar that has 69mm height, 10mm lower than OEM KTM bend. That is Protaper EVO bar called "steering stabilizer low". 51mm sweep. I also got this info from Xtrig today, which i think is not giving the full picture of handlebar height after ... more »

Added reply in a thread Sxf 450 2018 and 2020 suddenly front end high? 8/9/2020 2:36 PM

Seems like only solution. To bad, have like 4pcs of OEM stock bar. Not sure if there is a bar that is as low as 68-69mm.

Added reply in a thread Xtrig Rocs and Xtrig PHDS on SXF450 2019-21 = 10mm higher bar? 8/9/2020 2:34 PM

Fuck that sucks. Really hate the stock bar mounts/clamps, just twist when you lay bike over.

Added reply in a thread K-tech spring cartridges 8/9/2020 2:33 PM

Just the single one for WP AER. Heavy as fuck, made bike very front end heavy. Could not ride with it. Went CV and also KYB and bike was much better balanced.

Added reply in a thread Xtrig Rocs and Xtrig PHDS on SXF450 2019-21 = 10mm higher bar? 8/8/2020 8:02 AM

Is your part numbers Xtrig Rocs (40505003) and Xtrig PHDS (50200001)?

Added reply in a thread Xtrig Rocs and Xtrig PHDS on SXF450 2019-21 = 10mm higher bar? 8/8/2020 8:01 AM

See below. When i did run it with PHDS and Rocs, i instantly felt bars was way higher. Went back to my factory clamp and stock bar mounts, height came back to normal when riding. Took the picture in the garage after the training today, so seem to get ... more »

Added reply in a thread Xtrig Rocs and Xtrig PHDS on SXF450 2019-21 = 10mm higher bar? 8/8/2020 7:59 AM

See picture. In the videos from Xtrig on Youtube, they mount the KTM with the fixed mount without spacer to get the right height i guess. But it also means, PHDS automatically raise the bar position?!

Seem maybe they have done this (user lower ... more »
Started new thread Xtrig Rocs and Xtrig PHDS on SXF450 2019-21 = 10mm higher bar? 8/8/2020 7:55 AM

Has anyone mounted this combo, and successfully gotten OEM height on the handlebar position?

This forum thread has 22 replies

Added reply in a thread Sxf 450 2018 and 2020 suddenly front end high? 8/8/2020 7:17 AM

... more »
Added reply in a thread Sxf 450 2018 and 2020 suddenly front end high? 8/8/2020 7:15 AM

So adding the xtrig PHDS to the xtrig clamp is 10mm higher than the fixed bar mounts from xtrig that has partnumber 50200001.  I dobt know if xtrig fixed mounts is intended to be -10mm with the fixed bar mounts "as is", or, if they intend that to compensate ... more »