Yotam's Forum Activity

Reply to Honda wheels, CR250 swingarm 9/29/2018 11:26 AM

can you please check about shipping to Israel? i might take your front wheel thanks yotam21@gmail.com

Reply to STIC Metering block Jetting 9/23/2018 8:29 AM

Does NECJ could work better than NOZH i have now? I have ordered 38mm PWK with the right set up but it will take 3 weeks before i will get it (crazy Israeli customs cintrol...) But i found the NECJ in my tool box

Reply to Keihin PWK TPS connecting on CR125. 9/14/2018 10:08 AM

the 125 & 250 shares the same carb and same TPS (same PN) so i believe that same instruction should work is there any reason of getting a kit or something? as long as i know the wire colors that should fit each other i can use any connector that ... more »

Reply to Keihin PWK TPS connecting on CR125. 9/13/2018 11:16 PM

Well, i know that there is doubt about the influence of the TPS on the performance, some says that the throttle response increased and some they didn’t feel anything but it’s a discussion, after all, engineers decided to put it on their bikes for many ... more »

Reply to Keihin PWK TPS connecting on CR125. 9/13/2018 4:32 PM

Yeah i sent him message 2 days ago and he still didn’t reply If any one have his email shoot me a pm

Reply to STIC Metering block Jetting 9/11/2018 2:22 PM

Clear, done.

Reply to STIC Metering block Jetting 9/11/2018 8:35 AM

Thanks mate!!! There’s a holiday here, Tomorrow our Yamaha dealer will be available and i will purchase a 52 pilot and N3EJ neddle

Reply to STIC Metering block Jetting 9/11/2018 7:41 AM

George didn’t reply my email yet Waiting for him to answer I will order the 52 pilot and try it

Reply to STIC Metering block Jetting 9/11/2018 7:39 AM

I have NOZG & NOZF, it will take time until I get the needles i need Where i live dealers are not holding stocks like that

Reply to STIC Metering block Jetting 9/11/2018 6:01 AM

Are you running 38mm carb? Because the jetting supposed to be different between the 2 (i have 36)

Reply to STIC Metering block Jetting 9/11/2018 5:59 AM

52 pilot will not be richer than what i have now?

Reply to STIC Metering block Jetting 9/11/2018 12:00 AM

Seems like opening the air screw to 3.5 turns did very good job, the bike stopped “chocking” on low rpm but it is still feels like it’s little too rich, i will have to wait for the right needle I guess N3EJ is the first one to try

Reply to STIC Metering block Jetting 9/8/2018 1:51 PM

Got you,, i didn’t touched my air screw at all Just installed the stic and started riding Even cold start is pain in the ass... I hope that this is the problem

Reply to STIC Metering block Jetting 9/8/2018 1:37 PM

Thanks for the reply, just sent him an email. I am not sure about the air screw, i simply adjusted the it untill the bike was idling well

Reply to Wp Trax shock Kawasaki KXF 700$ Shipped 8/8/2018 12:59 PM

can i have dimensions please: clevis width, upper mounting width, shock total length center hole to center hole thanks.

Reply to Talon rear hub crf250/450 $85 shipped 8/8/2018 11:58 AM

thanks, i have Talon hub the gap can be seen on it as well?

Reply to Talon rear hub crf250/450 $85 shipped 8/8/2018 10:07 AM

i am not considering of putting new wheel on my old CR125 i am trying to figure if my wheel set is from new CRF or old i am not sure which year my wheel set was taken off

Reply to Talon rear hub crf250/450 $85 shipped 8/8/2018 7:21 AM

I bought CRF wheels 1 year ago and i think it was taken off CRF450 2014, i am not sure Any way; a new rear wheel on old bike will bolt on and cause trouble or simply eill not fit? I can see by your link that the gap is 3.5mm that means the wheel will ... more »

Reply to Talon rear hub crf250/450 $85 shipped 8/7/2018 10:12 AM

It doesn’t fit your CR250R as well?

Reply to Honda CRF Raptor titanium pegs SOLD 8/6/2018 11:37 PM

Pm sent