Added reply in a thread Steering Stabilizer Setup for 2014-2017 YZ250F --- $175 shipped 8/14/2020 4:30 PM

This probably fits a WR250F and maybe even YZ/WR450. You might consider relisting with more models in the title if you can figure out the fitment. GPR has great customer service and will probably be able to tell you over the phone.

Liked a bike check cr250 2002 8/14/2020 2:28 PM
cr250 2002
Started new thread Fork and Shock Shipping CT >> CA $? 8/13/2020 8:00 AM

Moving a set of Yamaha WR suspension from CT to CA, can a vitard please give me a rough shipping cost so that I can make a fair offer that covers shipping. How about $65?

This forum thread has 10 replies

Added reply in a thread Trick Parts from Luxon MX! 8/11/2020 2:54 PM

I followed Billy's 150 build and his level of commitment to engineering some excellent parts is pretty amazing.

Started new thread Wanted KTM 250SXF FC250 parts 8/4/2020 2:33 PM

Thought I would check here before I ordered this stuff through my local KTM shop: Searching for a few parts for my new (to me) 2017 FC250. This is a basic/budget restoration: - fork pump - bar pad - fork guards - frame guards - mx hand guards - shift ... more »

This forum thread has 4 replies

Liked a bike check 2020 KTM 300 XCW TPI 8/4/2020 1:51 PM
2020 KTM 300 XCW TPI
Added reply in a thread 2021 KTM AER forks 8/4/2020 9:56 AM

Hearing/reading very good stuff about the 21 AERs. A few guys that test them back to back are seriously impressed at how the fork has been improved. Shootout time is usually where they get bashed … we'll see shortly.

Added reply in a thread New Bell Helmets 8/4/2020 8:55 AM

So much potential in that MC replica (color, finish, shapes), but it looks like they used the first draft of their design as final. That darn red band on the side looks like a saggy goggle strap. I have a bell street helmet with a similar design where ... more »

Added reply in a thread KTM 450Sxf Seat Cover 8/3/2020 4:47 PM

2018 cover will not work/fit on a 2020 KTM unless its from a FE 2018.5.

Added reply in a thread FC250 Husky Wiring and E-start problem 7/24/2020 10:29 PM

I figured out by referring to the manual that one 10A fuse is active on the red side of the relay. the other on the black side is a spare. Both fuses looked fine but one was not continuous so dead . Despite finding this and confirming 10a fuse is good, ... more »

Added reply in a thread FC250 Husky Wiring and E-start problem 7/24/2020 10:25 PM

It’s a FC250 so the earth strap runs to the coil instead of the subframe like the KTM. Cleaned and confirmed negative battery terminal connection and coil mounted earth.

Added reply in a thread FC250 Husky Wiring and E-start problem 7/24/2020 4:53 PM

Still no start … bump if you have any ideas.

Liked a bike check 1996 YZ125 7/23/2020 1:20 PM
1996 YZ125
Liked a bike check 2016 FC350 7/23/2020 1:19 PM
2016 FC350
Added reply in a thread Gold Valve on KTM 450 2019 7/22/2020 10:28 AM

I would send them an email. You might also repost your question in the Tech Help forum.

Added reply in a thread FC250 Husky Wiring and E-start problem 7/22/2020 9:10 AM

I didn't have any measurable DC volts/power at the kill switch, but I was able to start the bike by jumping the relay. The power was being blocked by the relay. So I pulled out the relay and did the 12V test and am getting no click. So I'm ordering a

smile
... more »
Added reply in a thread Complete part out - '14 YZ250F - 7/21/2020 1:42 PM

How much for complete fork cartridges and damper rods? PM please.

Added reply in a thread FC250 Husky Wiring and E-start problem 7/21/2020 1:07 PM

The two 10A fuses beside the battery? Yes, checked those last night too and they were fine.

Added reply in a thread FC250 Husky Wiring and E-start problem 7/21/2020 9:01 AM

Added reply in a thread FC250 Husky Wiring and E-start problem 7/21/2020 8:59 AM