Added reply in a thread 2008 RMZ Restyle Kit 3/26/2020 8:30 AM

None of these available. I made the 2015 plastics fit my 07 a couple of years back (except for the tank shrouds). See my bike check. I cannot remember what needed to be done though, I recall some subframe mounts fabrication and rear fender mounting points ... more »

Started new thread 3D printing a respirator, open source 3/25/2020 8:23 AM

I know it's not necessarily moto related, but I also know it concerns all of us, as CoVid19 is a threat to us and everyone we know. You've probably heard that somewhere in the world people printed the missing valves on the 3D printer for the respirator. ... more »

This forum thread has 10 replies

Added reply in a thread WP Cone Valve forks KTM Husqvarna '16+ 3/23/2020 10:32 AM

Yes

Added reply in a thread YZ 250 Hubs and Rotors - Brand New! $250 OBO 3/20/2020 9:14 AM

Could you post the rear hub width? Rear sprocket to disc distance.

Added reply in a thread Rmz 250 forks 3/19/2020 3:15 PM

They should, assuming the steering stem length is the same. Keep in mind you will have to drill some new holes in your 2013 fender to make it fit 2009 triple clamps.

Added reply in a thread Rm top clamp question 3/19/2020 3:00 PM

05 top clamp will not work. If I remember correctly 01-03 used 24,5mm offset clamps, and 04+ used 22,5mm offset clamps. You would have to get upper + lower clamps as a set.

Added reply in a thread WP Cone Valve forks KTM Husqvarna '16+ 3/19/2020 6:30 AM

Started new thread WP Cone Valve forks KTM Husqvarna '16+ 3/19/2020 6:27 AM

Update: SOLD. Good morning gents, Up for sale a set of Cone Valve 48mm forks for KTM/Husky bikes. 2016+, small axle. Set up for approx 170lbs MX Paypal as F&F or buyer pays 4% fees. Shipping usually takes up to 5 working days, may be slightly longer ... more »

This forum thread has 16 replies

Added reply in a thread Looking for that crisp sound 3/3/2020 3:02 AM

Combination of perfectly dialed jetting and a shorty silencer I believe. Reeds might contribute too, but don't quote me on that. Doesn't make a whole lot of difference which muffler in particular. I have a bill's mx2 on my RM and it sounds flawless (I ... more »

Added reply in a thread Once again, Barcia 2/18/2020 4:31 AM

If my memory serves me right they did that for a short while somewhere around 15/16'? It was pretty awesome.

Added reply in a thread Handlebar replacement 2/7/2020 6:57 AM

You're welcome mate, you will slide the throttle off once you undo the bolts.

Added reply in a thread Handlebar replacement 2/7/2020 6:21 AM

From the underside of the throttle. Pull the rubber cover to the side, and there you have 2 bolts that hold the throttle in place.

Added reply in a thread First 2-stroke. Help me speak with my wallet! (Edit: wallet has spoken) 2/7/2020 2:31 AM

Another crazy idea: get a used 125 AND a used 250. 2 is better than 1!

Added reply in a thread WTB / ISO 2006 RM250 Inner cartridge - Showa 2/6/2020 4:05 PM

I think this should do the trick sdi rebound rod

Added reply in a thread aer48 to kyb sss conversion write ups 2/5/2020 3:00 PM

Might be worthwhile to ask a couple of reputable suspension shops for a DIY on this. Quite possibly there will be someone willing to share the details.

Added reply in a thread aer48 to kyb sss conversion write ups 2/5/2020 2:13 PM

There is way more to it AFAIK. Look at it this way, if you were a suspension tech, would you be willing to give out a DIY solution for something that cost you your time, money, R&D, tooling and some thought to sort out and make it work properly?

Added a comment to Turbojez's bike check 2/4/2020 1:32 AM
2007 RMZ 250

Hey Jonny, they were off a 2015 (I think) rmz 250. Front shrouds were 07-09. Other plastics were adapted from a newer bike

0 0 0

This setup has 3 comments.

Added reply in a thread Rough choppy exits of turns 1/31/2020 5:17 PM

Technique or suspension wise? I would start with speeding up the rebound on the rear shock. Try different stuff, trial and error. You need a pretty fast rebound on chopped tracks. Trax shocks deal with acceleration bumps really well.

Added reply in a thread Suzuki's With Gold (Yellow) Wheels 1/28/2020 11:37 AM

And you say that based off what? My rims are 14 years old now, might be something wrong with my eyes but they still seem quite yellow to me...

Added reply in a thread Garage sale, RM/RMZ trax, honda a-kit triple clamps, KX/KXF ohlins 1/28/2020 5:06 AM

Still have the triple clamps if that's what you're after. As a matter of fact it's the last thing I have from all that I posted here.

wink