Added reply in a thread Show me your Kx125/250 8/30/2019 12:48 AM

My 2001 kx125. It has a complete crf250r front end with a oversize rotor, wheel ect. Honda rear master, kx500 rear brake pedal and a couple more custom parts I made myself. I will get some more photos

Added reply in a thread 2 Strokes are dead!? 8/27/2019 1:53 AM

Got to do some testing on my kx125 a few weeks ago, it was a ground up build and has a few things that need to be sorted. Awesome fun.

Added reply in a thread Workschassislab 8/23/2019 8:15 PM

Fixed

Added reply in a thread Workschassislab 8/23/2019 6:42 PM

That's exactly my plan after watching J walks YouTube vid. After watching his video that's what pushed me to try them. I have played with stock mounts with various holes drilled in them before on my old 2010 crf250r, but these fcp mounts look too bitchin ... more »

Added reply in a thread Wilson Todd mx2 mxgp 8/23/2019 12:13 AM

Says that in the article but its all "speculation". I think it's a good move for him. Be good to see Todd and Evans both go for it next year.

Added reply in a thread Workschassislab 8/23/2019 12:03 AM

Thanks Joe, yes I got the soft uppers and medium lowers. Thanks for the info 🤙

Added reply in a thread Workschassislab 8/22/2019 9:12 PM

Ordered mine last week, keen to test them out once in the land down under. Went soft and medium fronts for my 18 crf250r. Michael Lindsay, do you have a torque spec recommend or just factory spec

Added reply in a thread Magura hydraulic clutch (especially on a Yamaha 450) 5/17/2019 1:51 AM

Have one on my 18 crf250r and it's my favorite mod yet

Added reply in a thread YZ250F 2019 air box mods 4/9/2019 1:21 AM

In my opinion you could have made it look a lot cleaner. That looks rough in the photo provided.

Added reply in a thread 2017 CRF450R Refresh (wheelset) 3/27/2019 9:15 PM

Awesome build mate. The ECU mods are impressive!

Added reply in a thread Builds that get out of hand... 3/15/2019 12:29 AM

Ya cant make a post without pics come on. Show us the cr

Added reply in a thread Hunter lawrence 2/5/2019 2:06 AM

Follow both the Lawrence brothers. Jets been doing well, really want to see hunter outdoors!

Added reply in a thread Husqvarna FC 350 off-road build-FINISHED 2/5/2019 12:31 AM

Very nice bike mate. What are those triple clamps like with the chambers?

Added reply in a thread From the Beginning: The Story of Dean Ferris 1/25/2019 3:39 AM

Ferris is a bad ass, big fan of his. Following him closely on his adventure.

Added reply in a thread Kx 125 engine into kx250f frame 12/28/2018 1:32 AM

Off the top of my head you would have to remake cradle or Y piece on the frame, engine mounts, cylinder head mounts, blank fuel tank hole if its efi, fit petcock, maybe some brackets for cdi/coil ect. Maybe some radiator mods, Maybe some mods to line ... more »

Added reply in a thread RM125 2004. Full tilt titanium, coatings 12/27/2018 8:55 PM

Exceptional build mate! if it was mine I would add a x fun alloy tank and trim side numbers but that's just my liking.

Added reply in a thread 2004 CR125 12/27/2018 8:29 PM

Awesome build mate!

Added reply in a thread Lets See Your Pitbike Builds! 12/27/2018 8:21 PM

That's a cool build! Should have came like that stock!

Added reply in a thread 2005 CRF250R build 12/24/2018 11:19 PM

On the money, ano/kashima isn't a paint like process like cerakote making it tougher. I recently got some upper tubes anodized gold for $80 aus plus 20 postage. Its pretty cheap here!

Added reply in a thread 2005 CRF250R build 12/24/2018 2:37 PM

Love these crfs. That's so clean, here's another

I would replace it with another stock tensioner. Its been on there since the bike was new most likely.