Added reply in a thread Colorado Springs Area for a week-Tracks to Practice? 10/9/2021 8:55 PM

You are right, and no hate. I haven't been to IMI on a weekend in probably 18 months or more. I went in December of 20.... it was so windy ( not IMI's fault ) that I pouted like a school girl after spilling her Starbucks in my truck. Actually unloaded ... more »

Added reply in a thread Deegan 10/9/2021 5:43 PM

Not even a little.

Added reply in a thread Colorado Springs Area for a week-Tracks to Practice? 10/9/2021 2:47 PM

Aztec is good. Ram MX track ( right next to aztec ) has been good this year. I would say more vet oriented. well kept on the weekend. I personally avioid every other inch of the property. Leadville is running tomorrow. That spot is worth the hike if ... more »

Added reply in a thread Deegan 10/9/2021 2:41 PM

Exactly. Wish I could say that I cared

Added reply in a thread 19-21’ KTM/Husq FMF 4.1 $100 10/4/2021 9:39 PM

Hang that thing on the wall and put it to rest. Jesus H

Added reply in a thread Luxon MX Husky FC350 Build - Linkage, Swingarm, and Misc. Bits 7/10/2021 11:37 AM

Do you/Will you sell these?

Added reply in a thread 2018 ktm250sxf fuel pump 6/8/2021 3:51 PM

how many hours

Added reply in a thread 2019+ KX450 Fork Springs, & Engine Mounts 5/11/2021 7:36 AM

I got your DM and I sent the info to my friend. Thanks!

Added reply in a thread 2019+ KX450 Fork Springs, & Engine Mounts 5/10/2021 9:35 PM

friend is interested in the pipe. Dibs. send your cell or email please.

Added reply in a thread Webb deserves to be champ this year 3/14/2021 4:12 PM

Rolling Eyes

Added reply in a thread Collarbone recovery. 3/14/2021 4:08 PM

dont even try natural. unless you have nothing better to but waste time and money. Get it plated. You'll be doing push ups and riding in no time. Been there, done that.

Added reply in a thread 2017 FC 350 motor 3/14/2021 12:56 PM

Don’t know for sure but I say yes

Added reply in a thread KTM PARTS 2/11/2021 10:35 AM

Will you sell just the clutch plates

Added reply in a thread 250sxf just rebuilt and clatters and smokes..... 9/4/2020 3:20 PM

Sent you PM

Added reply in a thread 250sxf just rebuilt and clatters and smokes..... 9/4/2020 12:04 PM

Something is wrong Metal shavings in your oil? You’re sure that you’re not one tooth off in your timing? Did you confirm with the black mark on the crank and the cam marks? You know you can pull that bolt on the brake side of the case with the thick ... more »

Added reply in a thread 250sxf just rebuilt and clatters and smokes..... 9/4/2020 9:35 AM

Warm it up and don’t be afraid to rev it. Don’t red line it. But don’t be nice. Get that ring seated. Take it for a ride. Be nice to it for a few minutes. Then ride fairly normal. Don’t be barcia with it. But again, don’t be nice

Added reply in a thread 250sxf just rebuilt and clatters and smokes..... 9/4/2020 9:34 AM

I’m not too worried with the smoke yet. You’re probably being too nice to it and the ring hasn’t seared. That paired with the assembly lube. I don’t use a lot of oil at all when I do it Take that hydraulic tensioner out. Put it on your work bench. Push ... more »

Added reply in a thread Ktm hard parts sx150 extreme head insert? 9/2/2020 8:00 AM

RTEK on my 300. Someone posted here just yesterday complimenting that insert on the 150

Added reply in a thread What’s it worth? (KTM suspension) 9/1/2020 8:42 PM

I am running this Set up on my hare scrambles bike. 100 percent recommend. Very good stuff

Added reply in a thread 19 KTM 150 Fork Set Up 8/31/2020 8:39 PM

The check plate still has to flex to allow fluid by, no?