Added reply in a thread 16 RMZ 250 Frame Guards 12/29/2018 6:50 AM

I have just tried to fit a pair of the new Acerbis frame protectors to my 2017 rmz250. The right side guard is a really bad fit to the point where it almost looks like it must be for another bike. Not happy with them at all. Has anyone else bought a ... more »

Added reply in a thread 2017 rmz250 judder spring 4/26/2018 1:46 AM

Thanks again Russ. I feel confident I've done the right thing now. We've got a 2 hour HH on Sunday and I'm not going to get much time to test it before then. Didn't want to be riding around thinking there was something missing that should have been in ... more »

Added reply in a thread 2017 rmz250 judder spring 4/26/2018 12:42 AM

Thanks for the replys. I have emailed Rekluse, but had no reply yet. The instructions that came with the Rekluse core exp 3.0 show a picture of the judder spring and say to install it. The Rekluse clutch hub is 97mm (approx.) and the internal diameter ... more »

Started new thread 2017 rmz250 judder spring 4/25/2018 4:10 PM

Hi all. I've just installed a Rekluse core exp 3.0. The Rekluse instructions say to install the stock judder spring and seat, but the Rekluse clutch hub is a smaller diameter than the stock hub. This means that the stock judder spring can't be used because ... more »

This forum thread has 6 replies

Added reply in a thread 2017 RMZ suspension for Hare Scramble 8/21/2017 4:28 AM

Fitted the bar risers on Saturday. Increased the fork pressure to 31psi and added some pre-load to the shock. I think the shock spring may be a little hard 50Nmm but not a million miles away. Initially I had tried to soften everything up by having lower ... more »

Added reply in a thread 2017 RMZ suspension for Hare Scramble 8/18/2017 3:56 PM

Ok, sounds good. I got some bar risers from the local mx shop after work this evening. I'll be able to drop the forks in the morning and get the geometry somewhere near where it was before I fitted the link.

Added reply in a thread 2017 RMZ suspension for Hare Scramble 8/18/2017 12:18 AM

I think you're right, I didn't actually ride the bike with the stock linkage and the first track I tested it on with the lowering link was unusually rough. Fitting the standard link should at least let me know what the bike could ride like before I mess ... more »

Added reply in a thread 2017 RMZ suspension for Hare Scramble 8/17/2017 7:50 AM

Ok, I have just checked Factory connections trouble shooting page. I'll probably print that off and take it with me to the track this weekend.

Added reply in a thread 2017 RMZ suspension for Hare Scramble 8/17/2017 7:31 AM

Hi, thanks for the reply. The first thing I did was use the racetech spring calculator to find out what shock spring I needed, so that's all sorted. Ordered from karlzracing here in the UK. I'm not sure what the lowering link may have done, it definitely ... more »

Started new thread 2017 RMZ suspension for Hare Scramble 8/17/2017 4:26 AM

Hi all, new member here looking for a bit of advice on suspension set up for a 2017 rmz 250 with psf2 forks. The bike will be used for 2 and 3 hour Hare Scrambles and MX practice. I'm hoping I don't have to send my suspension off for a re-valve and hoping ... more »

This forum thread has 11 replies

Added reply in a thread Basic RM250 Enduro/Woods Mods 8/15/2017 7:38 AM

Hi again Russ. Done the basics, bash plate, hand guards etc. I think the gearing is ok, in fact I was thinking of going the other way to give it a bit more top speed, the bike seems to pull really well off the bottom. My main concern is the suspension. ... more »

Added reply in a thread Basic RM250 Enduro/Woods Mods 8/15/2017 6:54 AM

Hi Russ, I'm also trying to convert an mx bike for HH here in the UK. I couldn't help notice you were referring to the last CEC race at LLansilin. I should have been there but my bike wasn't ready. Hopefully I'll be at the next one at Tyn Twll in a couple ... more »