Rohr144's Forum Activity

Reply to St Louis seats empty 3/19/2018 1:36 PM

Yeah I still would go as well. Kansas City is a better city overall.

Reply to St Louis seats empty 3/19/2018 1:19 PM

I only live about 40 minutes from downtown and I can also say that the city and the surrounding area is #shit

Reply to St Louis seats empty 3/19/2018 12:48 PM

I was at STL supercross saturday and it definitely had less people than last year. I think it was mostly because of St. Patrick's day but I'm not 100% sure. It's better like that anyway, we got to switch around to different empty seats to pick which ... more »

Reply to Drilling holes in piston for the exhaust bridge. 3/19/2018 8:01 AM

I'll take a pic later and post it on here. I was surprised when I saw that they were drilled.

Reply to 2015 YZ125 bogging with 32:1 mix 3/19/2018 7:00 AM

Also, the manual actually calls for 30:1 I'm pretty sure. I've even tried that and no bog either.

Reply to 2015 YZ125 bogging with 32:1 mix 3/19/2018 6:59 AM

Might have too big of a main jet. My 2006 YZ125 has all stock jetting with the air screw at two turns. I run 32:1 and no bog, wheelies out of corners.. Best thing to do is just take the carb off and check out what jets are in it.

Reply to What suspension settings are you using on your YZ125? 3/18/2018 9:40 PM

Good information guys, and easydoesit, my settings are pretty close to yours. I'm 140, and in the Midwest so its a wide spectrum of riding conditions, sand, loamy, soft, hard pack.. I made a few adjustments today and I found that stiffening up my sag ... more »

Reply to Drilling holes in piston for the exhaust bridge. 3/18/2018 9:37 PM

Just got a wiseco piston kit for my 06 yz125 on Friday. I also was wondering if it would have holes drilled in the piston for the exhaust bridge, and the holes were already there.

New thread What suspension settings are you using on your YZ125? 3/16/2018 8:46 AM

I have an 06 yz125 that I'm trying to get tuned to my liking. Does anyone have a baseline setting that they use for the forks or shock? Any information would help. Please also list your weight.

This forum thread has 5 replies.

Reply to 2005 RM125 Rebuild 3/16/2018 6:09 AM

Nice bike.. I had an 04. You're not kidding when you say the bikes don't have any low end power (I know 125s don't have alot down low but the RM has nothing!) I tried messing with gearing and going bigger on the back sprocket on the RM just makes you

... more »
Reply to Kick a** two strokes! 3/13/2018 1:51 PM

My 06 yz125. Drove 7 hours to buy it for $1700 and put about $1000 in it so far. First picture is what it looked like when I brought it home, second pic is what it looks like now. Third picture is the 2004 RM125 that I sold on the same day I bought the

... more »
Reply to Two stroke exhaust seal question 3/12/2018 6:10 PM

Just took the pipe off. After closer inspection, the rubber o rings are actually there. What isn't there is the metal spacer.

Reply to Two stroke exhaust seal question 3/12/2018 4:32 PM

If that's the case then they're definitely going in.. thanks man!

New thread Two stroke exhaust seal question 3/12/2018 2:10 PM

The part I'm referring to is circled in red in the picture. What exactly do these metal rings do? I bought my yz a few months ago, and when I did the top end rebuild, thone rings weren't there. I've been told that they can kind of adjust the power curve

... more »

This forum thread has 5 replies.

Reply to 98 KX125 any good? 3/9/2018 6:25 AM

I had an 02 Kx125 and had the most problems out of any bike I've been around.. obviously I mightve just gotten ahold of a bad one but I always steer clear of the green 125s. If found a Yamaha for cheap, parts would be more readily available and most ... more »

Reply to Osborne Vs. Forkner 3/3/2018 8:52 PM

Reply to Osborne Vs. Forkner 3/3/2018 8:31 PM

I mean forkner definitely cross jumped. Whether it was an accident or not. But does Osborne really have a good point to be upset? He's basically a man racing kids.

Reply to Osborne Vs. Forkner 3/3/2018 8:28 PM

Obsorne is 27 and racing in the 250 class or the "rookie" class and gets mad about someone making a rookie mistake? Hmm.

New thread Brand new DNA racing wheel with hub 2/27/2018 7:28 AM

Posting this for a friend. It's new and never used, was bought for a 2006 crf250r, but he sold the bike. I don't know what other bikes this wheel would fit. If you're interested, please text 6363123529. Price would be $250+shipping from Wentzville, Missouri.

... more »

This forum thread has 0 replies.

Reply to 2001 cr125 cylinder/piston 2/21/2018 6:22 AM

Definitely not reusable. Gonna need to be replated. And not sure what would cause your issue.