RockyRider

RockyRider

Lives in: Nor Cal, CA USA

Member since: 03/10/16

Recent Activity Filter:

Added reply in a thread 2016 KTM 250sxf cases/trans/clutch 3/6/2021 9:17 AM

+1 For Jeffro as a seller. Allowed me to buy that 3rd gear from him and was shipped with tracking. Got me back on the bike quickly

Added reply in a thread SXF 350 2017 -- loose crankshaft bolt 3/5/2021 12:00 PM

Like Tim507 said, nothing gained nothing lost. Loctite it back on to the correct torque and go on with your rebuild. Throw an aluminum oil pump gear in there and a manual timing chain tensioner and call it a day. Could've been bad but it wasnt, be happy. ... more »

Added reply in a thread 2016 350 SXF engine parts help 3/4/2021 9:39 AM

Just went through the same searching process on my '18 250f.. you are gonna have to do mainly oem. I bought a Pro-X rod and sent it to race tech to have it rebuilt (highly recommend, quick turnaround and fair pricing). All new OEM bearings in the motor ... more »

Added reply in a thread Showa Cartridges in WP Forks? 2/21/2021 9:43 AM

This is the info i needed, thank you!

Added reply in a thread Showa Cartridges in WP Forks? 2/19/2021 2:12 PM

Not saying the Showas are a ton better this or that, I just enjoy tinkering and trying new oddball things out. I prefer Showa over KYB so I wanted to see if it's possible. Maybe I'll try and find a junked set and see how it could be possible

Started new thread Showa Cartridges in WP Forks? 2/19/2021 9:25 AM

After doing a little research I've read a few people that have swapped the guts out of Showa forks into the WP AER's. However I cannot find any info on it. Found a few Euro websites that sell a kit but the price is a little much. I'm wondering if anyone ... more »

This forum thread has 11 replies

Started new thread WTB Quick Fill Screw Cap for dry break tank 2/10/2021 7:47 PM

Looking for a screw cap setup to put on my IMS dry break tank. Having issues getting a new unit shipped to CA

This forum thread has 1 reply

Added reply in a thread ISO 2018 KTM 250SXF 3RD Sliding Gear 2/9/2021 10:02 AM

Thank you for the input! I had the superseded part and it still pitted out on me, but I was able to find it out of a low hour bike so we're all good.

Started new thread 2016-2018 KTM 250/350/450 SXF and XCF Fuel tanks 2/6/2021 3:49 PM

Title states it, a stock SX tank and stock XCF tank both in perfect condition. No fuel pumps included, $100 OBO for each harrisonshannon118@gmail.com

... more »

This forum thread has 1 reply

Started new thread ISO 2018 KTM 250SXF 3RD Sliding Gear 2/6/2021 9:52 AM

Like the title says, looking for a take off if someone happened to grenade one of these motors. Crank went out and upon inspection I found this gear pitting and falling apart.

This forum thread has 3 replies

Added reply in a thread ISO 2019+ 250sxf stock exhaust 1/3/2021 5:21 PM

Not sure if they changed from 18 to 19 but I've got a brand new OEM system from an 18 250SXF

Added reply in a thread WTB 08 YZ 250 cnc triple clamps, FMF Pipe 6/17/2020 9:15 AM

I've got a set of black Ride's 22mm offset. $150 plus shipping

Added reply in a thread Multiple Sets of Ride Engineering Triple Clamps YZ/YZF 6/10/2020 8:13 AM

no, all i have are the two top clamps

Started new thread Multiple Sets of Ride Engineering Triple Clamps YZ/YZF 6/9/2020 7:18 PM

For sale are some Ride engineering Triple Clamps. I'll post the part numbers and ID's of the clamps for each set so you can decide if it will work for you or not. Also have two Pro Circuit top clamps. Asking $150 per Ride set, and $75 for PC top clamps.

... more »

This forum thread has 3 replies

Added reply in a thread size 11 fox and sidi boots for sale 5/30/2020 12:58 PM

PM sent for the red pair, if you could email me back I'd appreciate it harrisonshannon118@gmail.com

Added reply in a thread WANTED- Pro Circuit clamps 48mm/04 YZ250 5/28/2020 5:32 PM

I've got a couple sets, can you check on the top and bottom ID's so I can make sure they're the right ones?

Added reply in a thread 04 rm125 restyle kit 5/19/2020 9:32 AM

How much?

Added reply in a thread Suspension and triple clamp gurus please help! 5/17/2020 1:02 PM

Worst case scenario bore out that top clamp a mm or two to get it to move further down

Added reply in a thread Oil leak after Service WP Cone Valve 5/17/2020 12:59 PM

It's the o-ring where you unscrew the valving stack from the cartridge. Might have pinched it when they put them back in

Added reply in a thread 99% finished 2005 KX250 rebuild turned project bike 5/4/2020 9:19 AM

what he said! ^