Added reply in a thread 2009-2012 crf450r 2010-2013 crf250r crm composite gas tank 10/26/2019 6:14 PM

What capacity does it hold?

Added reply in a thread Fugly kawis 10/26/2019 6:11 PM

If it’s the one sold at Lowe’s it’s really an MTD mower. They change the colors on them from green to orange yellow etc but they’re all Made by MTD.

Added reply in a thread Lt500r quadzilla engine conversion into mx frame 10/7/2019 7:15 AM

I can’t believe you found a way for that engine to fit! You’re very determined! The quadzilla English be came with very conservative porting. Terry Varner said he built some race quadzillas back in the day that ran very well.

Started new thread WTB cheap 09 and up crf450r or 10and up crf250r forks 9/30/2019 7:58 AM

Can be air forks and or forks that need seals bushings etc. just want to spend around 200 on forks for a project bike. Thanks Jdemski1@aol.com

This forum thread has 1 reply

Added reply in a thread Herlings out, again :-( 6/17/2019 8:13 AM

Yeah JS7 had some nasty crashes for sure! I remember watching this one at Daytona and it wasn’t even one of his bad ones. https://m.youtube.com/watch?v=5oEKAIUroIU

Added reply in a thread Is Suzuki giving up? 6/9/2019 4:52 PM

I agree. Roczen and Tomac Would be crushing it on the Suzuki if that’s what they were signed to ride. The info from magazines should not be taken seriously. You know the the go to advice, “every bike needs one more tooth on the rear sprocket, run a pc ... more »

Added reply in a thread Suzuki rm 125 porting 6/7/2019 8:51 AM

Most notable porting changes usually start in raising or lowering ports two strokes. Like Ryan said above a quick check of exhaust port height will help to see if it was a clean up or actual porting

Added reply in a thread WTB Yzf 50mm spring 5.6-5.8 6/7/2019 6:17 AM

I have a 5.7 oem one off of a 13 yz450f. Jdemski1@aol.com

Added reply in a thread Cr500 in an aluminum frame 5/23/2019 3:53 AM

What pipe is on it?

Added reply in a thread MUGEN 125 5/15/2019 8:30 AM

It’s a golden hens tooth!

Added reply in a thread yz250 2t crank options balance ? aftermarket, oem ? 5/13/2019 9:06 AM

Sounds horrible. Just get the oem one trued before you put it in the bike unless the packaging has improved recently.

Added reply in a thread WTB: 09-12 Crf 450 kit suspension & vortex ign , aftermarket wheel sets 5/12/2019 11:51 AM

They’ll fit. Just need to run the 09 and up clamps to be right.

Added reply in a thread yz250 2t crank options balance ? aftermarket, oem ? 5/11/2019 5:40 PM

I think they got their shit together and knew if they sold shit cranks there would be no future for them. People think I’m crazy but I took a new hot rods crank out of a yz250 2t and put in a new oem Yamaha crank from that shitty oem box and it vibrated ... more »

Added reply in a thread yz250 2t crank options balance ? aftermarket, oem ? 5/11/2019 1:13 PM

The oem cranks come in a box with minimal padding. Some of them are padded terribly. It will need to be trued if u want minimal vibration. According to Cooksey crank works the hot rod cranks as of late come very trued. I put a lot in ppls bikes and never ... more »

Added reply in a thread 2018 Yamaha 450 *Update, found the problem 5/11/2019 1:08 PM

Sounds like it ate dirt or had an oil related failure.

Added reply in a thread Serious Aldon thread 5/11/2019 1:04 PM

He has them training like a race horse and thinking like a bumble bee.

Added reply in a thread 2017 CRF 450 Fork and shock springs 5/10/2019 6:45 PM

Im interested in just the shock spring. Let me know if you’ll separate. Jdemski1@aol.com

Added reply in a thread Bikes you are GLAD you sold.. 4/27/2019 10:30 AM

2009 ktm250sx. Handled terrible, engine hit in mid hard then signed off and out, vibrated. Revalved by FC, RG3, and mx-tech and still felt like crap.Conditioning

Added reply in a thread Squash 4/21/2019 4:06 AM

Call eBay tomorrow and explain to them what happened. They’ll go through the emails and hopefully remove the fees. Good luck!

Added reply in a thread How was your ACL recovery? 4/18/2019 11:27 AM

I had an acl with hamstring graft in 1999. Skip to 2018 and had a revision due to the graft stretched out and doing nothing. It was terrible the second time. Fevers, swelling, etc. had to go back in for a rescope washout and debridement to figure out ... more »