Added reply in a thread 2020 rmz250 part out 1/14/2021 12:27 PM

Andrew, I was wondering if you can email me at nate_billups2@yahoo.com. I was interested in a few of the parts you listed. Thank you

Added reply in a thread WTB- 2004+ RM250 skid plate carbon, plastic 1/11/2021 1:31 PM

NOS DSP Carbon https://www.ebay.com/itm/Nos-Dsp-Carbon-Skidplate-RM250-RM-250-2001-and-UP/333052919998?hash=item4d8b8040be:g:I~0AAOSwUpFcV00F

Started new thread WTB: Works Suzuki RM-Z450 billet rear brake pedal 1/9/2021 4:27 PM

I am looking for a Works Suzuki RM-Z450 billet rear brake pedal to finish off a build I have been working on for a while now. I am also interested in other works Suzuki parts if anyone is looking to sell them.

This forum thread has 3 replies

Started new thread '17 RCH Suzuki build question 1/2/2021 3:17 PM

I have a '17 RCH Suzuki RM-Z450 bike build that I have been working on over the last year or so and I have a question that will probably be hard to answer. In '17 they started using the Yoshimura RS-12 exhaust on the RCH race bikes but Yoshimura never ... more »

This forum thread has 1 reply

Started new thread 05-07 CR250 Left side engine case 9/11/2020 1:13 PM

I have a brand new 05-07 CR250 left side engine case for sale $225 Part number 04992-KSK-730

... more »

This forum thread has 1 reply

Started new thread 2 carbon fuel tanks for ‘08-‘17 RM-Z450 Yoshimura Suzuki/RCH Suzuki 9/11/2020 1:08 PM

I’m selling 2 carbon fuel tanks for ‘08-‘17 RM-Z450 used by Yoshimura Suzuki/RCH Suzuki. Both tanks are used but in great condition. I’m trying to offload these quickly and The prices reflect that. I guarantee you won’t find a carbon tank used by a factory

... more »

This forum thread has 2 replies

Added reply in a thread (Need gone, any reasonable offer will be accepted) Works Suzuki Parts 9/9/2020 8:52 PM

There’s a good chance it will fit but because it’s an RM-Z250 pedal you may need a spacer to clear the clutch cover on a 450. Sorry I can’t give you a definite answer.

Added reply in a thread (Need gone, any reasonable offer will be accepted) Works Suzuki Parts 9/9/2020 7:33 PM

My bad, both tanks are 450 and should fit ‘08-‘17

Started new thread Pastrana M2R helmet 9/9/2020 10:17 AM

Found this old Pastrana M2R helmet while going through boxes. Not in terrible shape. $75 shipped in the US

... more »

This forum thread has 1 reply

Added reply in a thread (Need gone, any reasonable offer will be accepted) Works Suzuki Parts 9/9/2020 10:09 AM

Really need these parts gone so they are not taking up space on my parts shelves, I’ll accept any reasonable offer.

Added reply in a thread (Need gone, any reasonable offer will be accepted) Works Suzuki Parts 9/7/2020 8:23 AM

... more »
Added reply in a thread (Need gone, any reasonable offer will be accepted) Works Suzuki Parts 9/6/2020 7:00 PM

Prices adjusted

Started new thread (Need gone, any reasonable offer will be accepted) Works Suzuki Parts 8/23/2020 6:42 PM

I have a few works Suzuki parts I don’t need anymore. All were collected for a project bike and are spares I did not use. Nate_billups@yahoo.com or 607-422-0331 -RM-Z250 standard length and extended billet brake pedals ($80.00) each

-Carbon ... more »

This forum thread has 11 replies

Added reply in a thread WTB: Factory Suzuki clutch cover 8/13/2020 5:07 PM

Good luck, there is a guy that makes a replica. I would go for that or settle for a standard Hinson cover.

Added reply in a thread Brand New 2007 Cr 250 7/15/2020 5:59 PM

$12,000 seems like the going rate for unused 2-strokes. I’ve seen 4 in the last few months.

Started new thread WTB: 2018-2019 RM-Z250 hubs 7/13/2020 7:38 PM

I know a lot of people have built custom wheel sets for their new RMZ’s. Does anyone have a new or like new set of RM-Z hubs or rims collecting dust that will fit a 2019 RM-Z250?

This forum thread has 2 replies

Added reply in a thread LOOKING FOR PRO TAPER FACTORY SUZUKI BARS 6/27/2020 11:32 PM

Completely understand man, I was just trying to explain I gave the guy an opportunity and dibs for a few days. Only stated my price so the other guys knew what I was asking. I don’t think the the guy wants my bars, I haven’t heard back from him all day ... more »

Added reply in a thread LOOKING FOR PRO TAPER FACTORY SUZUKI BARS 6/27/2020 10:01 AM

Not sure if your referring to the bars I offered up. The buyer was contacted and as of this morning he still has dibs on the Fuzion’s. Evo’s are still for sale. My asking price is what a new set of pro tapers cost plus shipping which I think is fair ... more »

Added reply in a thread LOOKING FOR PRO TAPER FACTORY SUZUKI BARS 6/25/2020 9:58 PM

I have one Fuzion and one Evo, let me know if your interested

Started new thread WTB: Showa A Kit forks for 2017 RM-Z450 6/14/2020 7:26 PM

Looking for a clean set of Showa A Kit forks for 2017 RM-Z450.

This forum thread has 4 replies