Added reply in a thread 1992 CR500R restoration 10/12/2018 9:59 PM

I got the exhaust installed along with a few other bits. Took a vid of the bike as its nearly completed. https://youtu.be/zjkTQwkxUrs

Added reply in a thread 1998 YZ250 budget build (my first smoker) 10/12/2018 9:14 AM

Frame looks good for a rattle can. As for the trans, I usually install the trans in the stator side case. Then you can install the star gear thing to the shift drum and spin it around to make sure your gears are all engaging correcting (check the speed ... more »

Added reply in a thread 1992 CR500R restoration 10/9/2018 5:36 PM

Thanks for the info. So I'm guessing there is no performance loss or gain (no combustion taking place that close to the exhaust port)? I suspected that it was a design for either performance, or some odd seizure damage. Either way, I have seen worse ... more »

Added reply in a thread 1992 CR500R restoration 10/8/2018 7:26 PM

Cleaned up the engine and took a peek inside:

Cylinder had these interesting markings above the exhaust ports. Not really sure what caused it?? Overall seemed like acceptable wear on the cylinder. No ... more »
Added reply in a thread 1992 CR500R restoration 10/4/2018 9:30 AM

Cleaned up the throttle, installed a OEM style grip, a new Motion Pro cable and installed the carb and got cable adjusted. Also installed the new UNI filter and a gas tank strap from 2004 CR250R. The CR500R strap was discontinued, and this one was only

... more »
Added reply in a thread 1989 CR250 rider/rebuild 10/3/2018 2:06 PM

Can't argue with that one! Nice score.

Added reply in a thread ISO someone who can replicate these graphics 10/3/2018 2:01 PM

Will it have the FX logo in the graphic? That's the only thing that bugs me with their replica graphics

Added reply in a thread 1992 CR500R restoration 10/2/2018 6:08 PM

Mag wheel spray cleaner. I've never had it actually clean anything and almost gave up on it, but it sure did work this time.

Added reply in a thread ISO someone who can replicate these graphics 10/2/2018 5:49 PM

If you aren't too picky on the details, I would suggest EVO MX. They won't be able to replicate the metallic silver, but a flat gray doesn't look too bad. Here are some 2002 graphics they did for me recently.

Added reply in a thread 1992 CR500R restoration 10/1/2018 10:45 PM

Tore into the carb. Notice the kink in the throttle cable!

Nothing out of the ordinary. Back together with fresh vent lines. I noted the jetting too: A/S = 1.5 Pilot = 52 Main = 172 Clip = 3 Needle = R7468N "S" Choke = didn't ... more »
Added reply in a thread 1992 CR500R restoration 9/30/2018 7:10 PM

I took the airbox back off to address the hole in the side and the crack on the bottom. I figured I'm handy enough that I can do anything, so I why not just fill the hole with melted plastic and sand it out?? I used a toothbrush that had seen better

... more »
Added reply in a thread 1992 CR500R restoration 9/29/2018 8:52 PM

I didn't have any lacquer thinner otherwise I probably would have tried it. The brake cleaner did evaporate quickly but that was ok because it was making the plastic soft. The sanding made the gummy plastic ball up and roll away. Then iI would spray ... more »

Added reply in a thread 1995 KTM 250 SX Build 9/28/2018 7:45 PM

I'm so jealous of this bike. I didn't pay attention to KTM until right about 1996 when a local dealer opened up and started selling them hard and by then they were always butterscotch and orange. I knew of the older white/red/teal bikes from obscure ... more »

Added reply in a thread 1992 CR500R restoration 9/28/2018 7:29 PM

I usually wait until the bike is done before putting the graphics on it, but they weren't storing very well so I figured why not?

Added reply in a thread 1992 KTM 250SX 9/28/2018 7:16 AM

central IL

Added reply in a thread 1986 Yamaha YZ250S 9/27/2018 9:34 PM

Great job on the resto! That is one of my favorite color combos!

Added reply in a thread 1992 CR500R restoration 9/27/2018 9:10 PM

These aren't the best pictures, but I ended up getting the stains out. I had to wetsand with brake cleaner if you can believe that. I also got the deformed and damaged area straight. I haven't figured out how to mend the crack (and make it look better!!!)

... more »
Added reply in a thread 1992 KTM 250SX 9/27/2018 1:21 PM

There was one local to me for $900 in running condition (rough). Had I known the parts would be easier to find I may have scooped it up.

Added reply in a thread 1992 CR500R restoration 9/25/2018 7:48 PM

I was hoping the airbox would go just as smoothly. Nope. The only good thing about it was my caked-with-dirt uni filter looks to be pretty new. I bought a new one, expecting the worst, but I'll keep this one for a spare. The airbox didn't clean up as

... more »
Added reply in a thread 1992 KTM 250SX 9/25/2018 9:06 AM

Wow, great site JMX82! I was just talking about a 92 KTM yesterday to a friend and the conversation ended with, "But I wouldn't know where to get half the stuff from." It's good to know there is stuff out there.