Added reply in a thread CRF 150R FINISHED! 10/14/2020 4:46 PM

She has, its a little small for her unfortunately. But I think it has plenty of power to haul almost anyone around. I had to replace just about every gasket in the carb, the slide, the choke and I put a JD jet kit in it. From what I've read the 07 needle

... more »
Updated bike check CRF150R 10/14/2020 11:19 AM
CRF150R
Updated bike check CRF150R 10/14/2020 11:19 AM
CRF150R
Added bike check CRF150R 10/10/2020 5:44 PM
CRF150R
Added reply in a thread CRF 150R FINISHED! 10/10/2020 5:22 PM

... more »
Added reply in a thread CRF 150R FINISHED! 10/10/2020 5:19 PM

Welp she's all finished up. Spent more than I would've liked but I think it turned out great! I tried to use as many local utah companies to help me and can honestly say they all did a great job. Wrap It Utah for the graphics, Throttle Therapy for the ... more »

Added reply in a thread CRF 150R FINISHED! 10/8/2020 7:41 PM

Ran into some problems with the carb. Wouldn't idle, which after a quick search on the internet sounds like a real common problem on these 150R's. Ended up taking it apart and putting all new gaskets , including mid body gaskets, new slide and a jd jet

... more »
Added reply in a thread CRF 150R FINISHED! 9/17/2020 8:40 AM

All the parts that were replaced from the motor. The previous owner said they didn't do an oil change right. I assume that means they drained the engine oil and added it to the transmission. The

top end did not fair well. ... more »
Added reply in a thread CRF 150R FINISHED! 9/14/2020 7:27 AM

The linkage is all steel and was kinda rusty, so it also needed some cerakote.

Added reply in a thread CRF 150R FINISHED! 9/7/2020 7:56 PM

Before assembling the motor, I did Checked how true the crank was...both sides were half of tolerance. So quality is still spot on.

Added reply in a thread CRF 150R FINISHED! 8/27/2020 6:19 AM

Motor is back together! Unfortunately while turning the motor over by hand I discover the camshaft was bent. Luckily hot cams makes a pretty good cam and I was able to install it this week.

Also got the swingarm buddies ... more »
Added reply in a thread CRF 150R FINISHED! 8/20/2020 9:05 AM

Probably, they really push the made in Japan stuff though, makes it a little frustrating. Better not catch the flu from this 😅

Added reply in a thread CRF 150R FINISHED! 8/20/2020 9:02 AM

That horrible yellow on the spring has to go, I tried using strip-eez and it got most of the powder coat off after an hour or so. I had to go back with scotchbrite and another coat of strip eez to finish it off. But it turned out great! Curious to see

... more »
Added reply in a thread CRF 150R FINISHED! 8/19/2020 2:13 PM

New bearings all around and some cerakote for the cases...anybody else bought a complete crank from pro x? Whats this bullshit?

Also got a instagram going on this bike @dirtbike_projectbuilds ... more »
Added reply in a thread CRF 150R FINISHED! 8/19/2020 1:57 PM

The frame and the swingarm turned out great from the powdercoater, but in my hast, when I ripped out the chain adjuster bolts all the threads came out with them

. So I thought I would give these "swingarm buddies" which is basically just a ... more »
Added reply in a thread CRF 150R FINISHED! 8/19/2020 1:07 PM

Most of the parts were randomly placed in trash bags and boxes and even had to fight off some black widows to get the cylinder back, But most of the parts were there. I quickly stripped down the frame and swingarm for powder coat and set my sights on

... more »
Started new thread CRF 150R FINISHED! 8/19/2020 12:59 PM

Well what started out as a quick flip for an extra buck has now turned into a cash grabbing monster, once I figured my wife should ride it. I picked this thing up covered in rust and full of leaves, it must've spent a winter or two in the elements cause

... more »

This forum thread has 24 replies

Added reply in a thread KTM Inner Clutch cover (ceracoated) ‘17-‘19 5/25/2020 6:55 AM

Well whatever it is, Looks freakin sweet.

Added reply in a thread KTM Inner Clutch cover (ceracoated) ‘17-‘19 5/25/2020 6:46 AM

What color of cerakote is that?

Added reply in a thread LECTRON Carburetors [HELP] 5/24/2020 7:08 PM

Their quality control isn't the best (had a issue in the past), but their customer service is very good. They will make it right, just call them.