Added reply in a thread WANTED SUZUKI RM 250 BILLET TRIPLE CLAMPS 9/23/2018 11:54 AM

Talk to Adrian with Ride Engineering. I couldn’t be happier with the fit and finish, option to run either fender, and the HPSD Mount is a much needed added bonus for the zuks.

Added a comment about feature Vital MX Pit Stop: Works Connection 6/8/2018 7:54 PM
C50_img_5727_1487777399

If it’s Works, it works! Can’t leave home without their clutch perch on all the bikes.

0 0 0

This feature has 24 comments.

Added reply in a thread 06 rm125 build! 6/3/2018 5:01 AM

Looks killer man. Go twist some grip!

Added reply in a thread RM125 2004. Full tilt titanium, coatings 5/30/2018 7:25 AM

Where did you find all our linkage ti hardware from. I was never able to find a complete set.

Added reply in a thread AFTERMARKET RM 250 WHEELS FOR DECENT PRICE??? 4/24/2018 12:40 PM

TCR Wheels killed the wheelset for my 125. Stock hubs were turned and coated like Slosh mentioned, and laced with a set of DID STX hoops. I’m very happy with the quality, and will never have an issue with flirting to find an odd-ball set of bearings/spokes ... more »

Started new thread 1989 YZ250 2/26/2018 11:35 AM

Seeing as my 04 RM125 is wrapped up, and singing her bubble bee song, another project had to take her place. Picked up a 99% original and complete 1989 YZ250 from a local buddy (date stamped original front and rear tire), and am super excited to see

... more »

This forum thread has 2 replies

Added reply in a thread Not another RM125... 1/29/2018 2:32 PM

The new fender should help, I’ve noticed the Acerbis feeders have a slightly tighter fit, that allows the square nut to hold a little better. If not, I would try to run a longer Bolt and add a lock nut

Added reply in a thread Not another RM125... 1/29/2018 1:52 PM

I use the square nut. I will say it is a back-asswards design that is easy to strip out plastics on. Not sure why you are not able to tighten it down enough, I have not had that on any of the RM125/250’s I’ve owned over the years.

Added reply in a thread Not another RM125... 1/28/2018 3:15 PM

Mine were Acerbis, but UFO makes the yellow as well. I trimmed them with painters tape and two sets of eyes to make sure everything was square. lots of measuring and fitting, but they’re dead buts even. Use a hacksaw blade and finish with a fine file ... more »

Added reply in a thread Not another RM125... 1/28/2018 10:21 AM

Finally have the Gutless Wonder back and running. Six months is up from the injury, and can finally swing a leg back over the bikes. Was able to pickup a new Guts seat cover and Phantom Foam and tons of Ti (axles and two linkage bolts are all that are

... more »
Added a comment about feature Vital MX 12 Days of MXmas: Day 5 12/12/2017 5:08 AM
C50_img_5727_1487777399

Does this put Christmas on level 100?

0 0 0

This feature has 314 comments.

Added a comment about feature Vital MX 12 Days of MXmas: Day 3 12/10/2017 8:02 AM
C50_img_5727_1487777399

This would sure be better than coal!

0 0 0

This feature has 318 comments.

Added reply in a thread WTB RM125 Parts 10/20/2017 7:21 AM

I’ve got a VForce3 with exactly 5.0 hours on it. I only pulled it off because it will not work with my new Keihin carb, and will rub on one of the bolts. If you’re interested, I’d be willing to let it go. PM me.

Added reply in a thread Looking for RM Seat 10/10/2017 5:35 PM

Thanks for all the response guys. Picked one up from Bman!

Added reply in a thread 04 cr125 snail 10/7/2017 11:44 AM

At the end of the day, it will always be a dead raccoon compared to a 450! Hahaha but that is the joy of the buck and a quarters. Let her sing without the 134 kit, keep it as close to stock as possible for longevity, and just ride it! I just went from ... more »

Added reply in a thread Looking for RM Seat 10/6/2017 11:40 AM

Bman I’m interested. Shoot me an email b.joyner41@gmail.com

Added reply in a thread Looking for RM Seat 10/5/2017 7:02 PM

Well shoot, that works! Complete seat or pan?

Started new thread Looking for RM Seat 10/5/2017 11:43 AM

As the title says, I’m looking for a seat for a 2004 RM125/250. Ideally, I just need the seat pan, but a decent condition seat may suffice. Anything from 01-08 will work. Any one?

This forum thread has 9 replies

Added reply in a thread Wich pipe and silencer? 9/13/2017 8:55 AM

If I'm not mistaken (this was 7 years ago) it was the 296 sparky that snapped. Too much weight for the single mount. Honestly, I'm debating my current setup and going for the Bill's MX2 Carbon and raw expansion chamber. Heard too many good reviews on ... more »

Added reply in a thread Not another RM125... 9/12/2017 8:19 AM

File to flush, sand with 400 grit and 600 grit for final, come back and hit with green or maroon scotchbrite pad with some WD40. The filing is the time consuming part.