Added reply in a thread Where to get a visor for Fox V4? 10/28/2013 7:37 PM

Found one on ebay by doing a search of v4 visors, a handful came up so I ordered one from ridersdiscount in Michigan for $28, says they have $10 in stock.

Started new thread Where to get a visor for Fox V4? 10/28/2013 7:17 PM

I did a faceplant today and destroyed my V4 visor. Called Fox and they didn't show any in stock but would get back to me in 48 hours. Probably be 10-14 days before they can get me one, need one in 4 days for race. Has anyone had any luck finding a visor ... more »

This forum thread has 5 replies

Started new thread Suspension fixable for a '13 KTM450sxf? 10/26/2013 7:21 PM

I've heard many 450sxf owners are unhappy with revalves on this bike. Is it possible to get good results from tuning these forks/shock or is the Ohlins or A-kit the only way out for decent expert level performance?

This forum thread has 34 replies

Started new thread Reason for Barcia's Honda DNF ? 10/20/2013 11:58 AM

I heard it was a mechanical problem with the engine ?

This forum thread has 40 replies

Added reply in a thread Jetting specs for '07 YZ125 PC pipe & Rad valve? 10/17/2013 5:21 PM

Well... PC says keep the 410 stock mainjet, use a 35 pilot (stock =40) and move the clip from the 4th groove from top to third; jetting does not change with reed valve upgrades. Boyesen says if the RAD valve is added and the stock pipe is used, drop ... more »

Started new thread Jetting specs for '07 YZ125 PC pipe & Rad valve? 10/16/2013 6:21 PM

Hi, Can anyone share their jetting specs for a stock '07 YZ125 ... I'm switching to a Pro Circuit pipe & silencer with a Boyesen Rad Valve, at sea level, 60-75 deg F ? Thanks !!

This forum thread has 4 replies

Started new thread Ragin Ron porting services 9/4/2013 6:53 PM

HI , I'm looking to get ahold of Ron Bushy, (aka Ragin' Ron) to get some porting done on my 09 YZ250 2t ... can't find him an internet search ... anyone know how to reach him? Thanks, Joe.

This forum thread has 3 replies

Started new thread Steel vs. aluminum frame stretch ? 8/27/2013 6:53 PM

Curious to see if there is any documentation of late model steel frames stretching over time with use? I recall in 1988 there was a Dirt Bike article that documented a maintenenace schedule of a CR250 over the course of a season. If memory serves me, ... more »

This forum thread has 3 replies

Added reply in a thread Replace female interviewers with retired ex-rac 6/8/2013 9:13 PM

During the Supercross season RC & Emig would interview the heat race winners right after they pulled off the track ... it was an honest, frank dialogue on what just transpired that was refreshing. The heat race winner being interviewed respected ... more »

Started new thread Replace female interviewers with retired ex-rac 6/8/2013 7:22 PM

I'd rather see retired ex-pro racers (Kdub, Holley, MC, Hughes, Lamson, Bradshaw, Dowd, anyone) interview the racers on the podiums, at starting lines, pits, etc. than the current female interviewers on NBC/Fuel coverage. We would get a better depth/quality ... more »

This forum thread has 40 replies

Started new thread What's with this Horse Sh1t ?? 6/8/2013 1:30 PM

Where's the moto? I'm just getting the Belmont BS!!!

This forum thread has 3 replies

Started new thread '06+ forks & shock fit on '03 YZ125 ? 6/7/2013 6:36 PM

Hi, I'd like to swap the newer 2006+ YZ 125/250 forks and shock on to my 2003 YZ125 for an upgrade. Has anyone performed this swap? Do the newer forks and trples interchange? Is the fork offest the same? Is the shock length the same? Linkage rising rate ... more »

This forum thread has 1 reply

Started new thread Suzuki RMZ250/450 for 2014? 5/19/2013 3:36 PM

Anyone hear when Suzuki is releasing info on the 2014 RMZ's? Any info / rumors available? Thanks....

This forum thread has 7 replies

Added reply in a thread Dean Wilson 3/17/2013 6:18 PM

Should have been wearing a chest protector, oh yea, but thats not cool

Added reply in a thread Pro Circuit triple clamps KX250 2006? 10/13/2012 4:58 PM

Get the 21.5mm offset triple clamps from Applied ... they make the bike's handling perfect! I got mine through thumpertalk for $376 without the stem, stem was and additional $90 installed. No other company makes the clamps in 21.5 mm offset (stock is ... more »

Started new thread Stillwell Performance Suspension for MX? 5/6/2012 4:52 PM

Hi - has anyone used Stillwell Performance for MX suspension revalving? I have a 07KX250 that I would like to revalve for MX, and am looking for an alternative to Factory Connectin. Thanks!!!

This forum thread has 2 replies

Added reply in a thread How to fix dents in exhaust? 1/15/2012 7:07 PM

We charge $60 to totally repair & clean your pipe. Check us out at FusionOneUSA.com Using the pressure & heat technique is very effective, but very dangerous if you do not take the proper precautions and use the correct safety gear. An exploding ... more »

Added reply in a thread Stripping stock exhaust paint 10/26/2011 4:20 PM

Use www.fusiononeusa.com- they'll strip it, polish and clear coat it for a small price

Started new thread Anyone use 05-07 KX250 2T RG3 21.5mm trip clamps 9/24/2011 9:42 AM

For more accurate handling? Thanks ... Joe

This forum thread has 3 replies

Added reply in a thread Anyone been to High Point? 5/31/2011 5:33 PM

What's the nearest airport to the track?