Added reply in a thread Misc RM 250 parts 11/24/2020 7:20 AM

Awesome. Your PayPal is the same as your email? Langhammx@sbcglobal.net?

Added reply in a thread Misc RM 250 parts 11/24/2020 6:51 AM

Interested in the head. What year RM is it for? If it fits an 06 I will take it! Johnchang22@yahoo.com Thanks, John

Added reply in a thread WTB 2006 RM 250 Hinson Pressure Plate 10/15/2020 1:35 PM

Okay, awesome! Please let me know. Thank you

Started new thread WTB 2006 RM 250 Hinson Pressure Plate 10/14/2020 8:51 PM

Looking for a Hinson Pressure Plate if anyone has one for sale. For a 2006 RM250 Thanks, John

This forum thread has 3 replies

Added reply in a thread 2006 RM250 “Stock” mod build FINISHED 10/7/2020 5:53 PM

... more »
Added reply in a thread 2006 RM250 “Stock” mod build FINISHED 10/7/2020 9:04 AM

Here is another view for you. The oem seal does slide down into the head tube about 3-5mm (if I had to guess without measuring). Hope this helps!

Added reply in a thread 2006 RM250 “Stock” mod build FINISHED 10/6/2020 8:10 PM

Triple clamps are already on the bike.. This is the best I could find from my pictures. How do the pivot works kit look like?

Added reply in a thread 2006 RM250 “Stock” mod build FINISHED 10/6/2020 12:36 PM

Every single piece has been cleaned and inspected. Now just time to build..

... more »
Added reply in a thread 2006 RM250 “Stock” mod build FINISHED 10/4/2020 10:26 PM

Suspension ready to go. DLC coating on the fork and shock tubes

... more »
Added reply in a thread 2006 RM250 “Stock” mod build FINISHED 10/3/2020 11:04 PM

I didn’t know...I need to call them right now! Lol. Thanks!

Added reply in a thread 2006 RM250 “Stock” mod build FINISHED 10/3/2020 10:11 PM

... more »
Added reply in a thread 2006 RM250 “Stock” mod build FINISHED 10/3/2020 9:50 PM

Cleaning with my hand and brushes looks okay.. but just not that good. Vapor Blast! .. The bottom of the the float bowl and the two circles near the bottom look like a face :I lol ... more »
Added reply in a thread 2006 RM250 “Stock” mod build FINISHED 10/3/2020 9:22 PM

Added a Hinson clutch basket and inner hub. The oem clutch plates are pretty much brand new so just reusing those.

... more »
Added reply in a thread 2006 RM250 “Stock” mod build FINISHED 10/3/2020 9:06 PM

Joined the vapor blasting bandwagon. It did not disappoint! Engine and Carb. Blasted the engine whole. Checked the powervalve and waterpump afterwards and nothing got inside.

... more »
Added reply in a thread 2006 RM250 “Stock” mod build FINISHED 10/1/2020 11:07 PM

Dude, that thing looks clean. I would have made the drive myself too! Haha Have you done anything to it since?

Added reply in a thread 2006 RM250 “Stock” mod build FINISHED 10/1/2020 10:28 PM

I think being in SoCal is a huge bonus. I've seen a few of these pop up over the past year in same or better condition.

Added reply in a thread 2006 RM250 “Stock” mod build FINISHED 10/1/2020 10:21 PM

Couple pieces from my other bike going onto this one. Pro Circuit linkage. Bearings cleaned and regreased.

RG3 Triple Clamps getting a new steering stem pressed in ... more »
Added reply in a thread 2006 RM250 “Stock” mod build FINISHED 9/28/2020 9:36 PM

Tearing it down

Factory grease is still clean. Touched up the frame. Bad lighting on the photos but didnt notice at the time.. ... more »
Added reply in a thread 2006 RM250 “Stock” mod build FINISHED 9/28/2020 8:21 PM

I have a lot of stuff from my other RM250 I want to transfer on to this.

Added reply in a thread 2006 RM250 “Stock” mod build FINISHED 9/28/2020 7:53 AM

Didn’t know they made a hop home service manual. That’s pretty awesome! Thanks for the info

grin