Jensenyo

Jensenyo

Lives in: SWE

Member since: 09/10/17

Recent Activity Filter:

Added reply in a thread WP shock rebuild. 5/15/2019 1:01 PM

Thanks for the tips guys! ? I went ahead and ordered that filling tool. Will look into the snowmobile shock service.

Started new thread WP shock rebuild. 5/15/2019 5:25 AM

Hello! I have searched around for a guide how to service an shock with floating piston instead of an bladder like most japanese brands use. Does anyone have one? Im guessing the compression adjuster needs to be removed and the piston should be in the ... more »

This forum thread has 6 replies

Added reply in a thread X Trigs on a 2019 ktm 250sxf 11/20/2018 6:03 AM

Keefer testing has a writeup on those clamps.

Added reply in a thread Ktm sxf250 2018 oem piston 10/16/2018 3:41 AM

Vertex in the the twostrokes and Carillo (cp) in the fourstrokes.

Added reply in a thread 2019 CRF250R or 2019 YZ250F? Help me decide. 9/14/2018 12:28 AM

Anyone who has experience of the 2019 yzf 250 compared to 2019 ktm 250f? Long time ktm owner here but the 19 Yamaha has got me thinking of switching to blue. I own an 2018 ktm 250f right now.

Added reply in a thread HELP. Swapping KTM Forks/Shocks 6/13/2018 3:59 AM

You probably should break the suspension in some but seriously give the stock stuff a chance! It's really good! I have had 16s and two 17s ktms all with airfork and my current 2018 250f is so much better than the older models! I run forks around 10bar ... more »

Added reply in a thread CRF450R 2018 4/23/2018 3:48 AM

Keefer keeps on saying the bike needs mineral oil to get the clutch to last decent, still fades some when getting hot. Just a thought, I have friends that ride red and they usually end up getting stiffer springs to the clutch also.

Added reply in a thread Ktm Valve check after 1 hour? 3/15/2018 11:44 AM

Does the manual state an 1h check? Have never heard of that. Have owned 4 KTM's from 2014 - 2017 and checked valves usually around 40h, not even once have any clearance been out of spec. And thats around 100h on each bike.

Added reply in a thread Renthal 994 on 2018 ktm 3/12/2018 4:37 AM

When I ran twinwall on my 350 I loosend the crossbar and pushed the mapswitch to the left of the barpad, thought that worked well.

Added reply in a thread Ktm 350 2/27/2018 11:03 AM

I have owned an 350 2017 too and I agree its a bit snappy at the initial throttle! I did put an 51 tooth rear and that made me able to use 3rd most corners. Also removed the baffle in the stock exhaust, was some job to do it with chopping and welding

smile
... more »

Added reply in a thread Understanding Sag... 2/16/2018 1:35 PM

That's the plan.

Added reply in a thread Understanding Sag... 2/16/2018 3:57 AM

Thanks for the tips, will measure spring preload and determine if I might need an 42 spring. And maby need to add preload in the front too. Going to ride sand next week and weekend, just hoping the temperature will be over 0 degrees celcius!

Added reply in a thread Understanding Sag... 2/15/2018 12:35 PM

Sure. I have ttx cartridges in my aer's at the moment, with 4.7 springs in them. clickers are stock 14/14 and forks at first line. On the shock i have an 40nm spring, around 35mm static and 107mm riding sag. Have messed around some with the clickers ... more »

Added reply in a thread Understanding Sag... 2/15/2018 9:13 AM

Talking about sag and suspension, I have always liked a bit more sag on the my ktm 2016 and forward. Have owned 250f 350 and now 250sx. I feel that I loose a lot of traction when running less than around 107-110 sag in the rear with forks on the first ... more »

Added reply in a thread 17' TC250 Jetting Help 2/6/2018 7:33 AM

I recall that the 125/150sx calls for 1:40 mix ratio, but I can be wrong. Check your manual.

Added reply in a thread KTM,Husky 250,300 cheap HP 2/6/2018 12:30 AM

Which spring is it compared to on the dyno? Green?

Added reply in a thread Live stream rip-off. 1/14/2018 5:22 AM

Whatever you do.. Don't buy the vod cause it's barely watchable either! Lags like crazy.. Resolution is good but man.. Sometimes it looks like slowmotion pictures! I want my 150$ back.

Added reply in a thread 17' TC250 Jetting Help 12/20/2017 1:02 PM

I did check squish on my stock 250sx 2017 and got just under 2mm (!) which equals to almost 0.080" said google. Having trouble jetting my bike aswell, especially since I run some more technical stuff in cold Sweden atm. Stock jetting has worked good ... more »

Added reply in a thread 2017 Husky 350 aer 48 set up.. 11/14/2017 11:51 AM

Sounds to me like you have the bike set up a bit too much front end biased with low sag numbers and also forks high up in the triples. I would start going to atleast 103-108 sag and put the forks at the 2nd line. What pressure are you running? Also the ... more »

Added reply in a thread Just bought a 2017 Husky TC250...any setup tips? 11/4/2017 3:59 AM

Speaking of setup tips, im nearing an top end check /replacement. Does anyone know what squish I should aim for with the base gaskets. I meassured squish stock and it was about 1,9mm which seems a bit much even with pump gas.