Added reply in a thread CR500 Coke Bottle Swingarm 7/7/2018 8:33 AM

Here is what an HRC coke bottle swingarm looks like.

Added reply in a thread CR500 Coke Bottle Swingarm 7/7/2018 8:25 AM

It looks similar to the replica coke bottle swing arms KLP Racing make. You could try contacting them to see if they made it or not. You scored on a $1500 swing arm if it was made by KLP racing. http://www.klpracing.com/id12.html

Added reply in a thread Allsport Dynamics IMC Lacer Wrist Braces 7/6/2018 9:47 AM

I will take them both. Email me at jmc247@gmail.com

Added reply in a thread Wanted to Buy: 1990's HRC magnesium clutch cover for an RC250 6/6/2018 6:50 PM

You can ask doc wob on eBay if he has one left. If your fine with some replicas, I found a set on eBay: https://m.ebay.com/itm/HONDA-CR-250-HRC-RACING-REPLICA-clutch-ignition-cover-Works-Factory-no-Boyesen-/163081445352 Or you could possible find one ... more »

Added reply in a thread Flat landing/casing tips 5/31/2018 5:03 PM

Best advice I can give you is to try not casing an uphill triple like I did.

Added reply in a thread Flo yellow ktms 5/17/2018 9:58 AM

I have a Husky is flow yellow which is technically a KTM.

... more »
Added reply in a thread 1999 KX 250 5/1/2018 9:14 AM

Could you shorten my shock body if I sent it to you, I can't find a local machine shop that I can trust enough to cut it. My plan was to find a used shock off eBay as a test dummy to see if I can get it to fit in an 89 cr250, if it worked I would then ... more »

Added reply in a thread 1999 KX 250 5/1/2018 6:10 AM

Did you shorten the shock body yourself or have a machine shop do it because I'm trying to do the same thing with a 16 kx450f shock body to fit in an 89 cr250 build I'm doing. The Kxf shock was the closest Length I could find compared to the stock 89 ... more »

Added reply in a thread 1989 CR250 fork conversion build 4/20/2018 6:13 AM

Test fit the caliper and oversized rotor

Next thing on the list is get the front hub powder coated black and lace it up to a vintage gold rim. ... more »
Added reply in a thread 1989 CR250 fork conversion build 4/15/2018 7:20 AM

Just received galfers 280mm Tsunami oversize kit.

And a brake line ... more »
Added reply in a thread 1989 CR250 fork conversion build 4/9/2018 7:53 PM

Just received the most expensive brake upgrade I have ever done.

... more »
Added reply in a thread 1989 CR250 fork conversion build 4/9/2018 7:35 PM

If your going to use a NOS 92 silencer I would look at pictures of it side by side with a 92 pro circuit silencer just to make sure they look somewhat the same. From pictures the NOS silencer mounts at a slightly different angle than the pro circuit ... more »

Added reply in a thread 1989 CR250 fork conversion build 4/9/2018 5:35 PM

I have a full picture of it before I started the fork conversion.

Added reply in a thread 1989 CR250 fork conversion build 4/9/2018 1:52 PM

Ordered it last week, should be here today or tomorrow.

Added reply in a thread 1989 CR250 fork conversion build 4/9/2018 11:41 AM

Here is an original with the 89 silencer in front of the rear fender

Vs the 92 ... more »
Added reply in a thread 1989 CR250 fork conversion build 4/9/2018 11:22 AM

The 92 silencer fit on perfectly without modifications. the 89 silencer and 92 had a slight difference with mounting points, the 89 was mounted in front of the rear fender using a large spacer behind it to fill the gap whereas the 92 is behind the fender ... more »

Added reply in a thread 1989 CR250 fork conversion build 4/2/2018 10:23 AM

It's been fixed and looking good.

Also added some factory HRC shroud decals. The subframe was slightly bent from my crash, so I unbent it. I also needed a new silencer so I got a 92 cr250 silencer with a stinger tip. ... more »
Added reply in a thread 1989 CR250 fork conversion build 4/2/2018 7:53 AM

Thanks for all the replies, drilling and tapping into the top clamp would be the easiest. It's still going to need a small bracket that hangs down for the front plate to bolt up.

Added reply in a thread 1989 CR250 fork conversion build 3/31/2018 2:01 PM

Made a special bracket for the front

But it's ugly looking when the plate sits this far out... more »
Added reply in a thread 1989 CR250 fork conversion build 3/31/2018 9:13 AM

Next part on the list is a works caliper from Motostuff.