Added reply in a thread Team Honda 93 pics? 8/14/2017 12:29 PM

That last one, has a creative mind made it, or has it actually been riden? Thought these graphics where only on plastics from 1995 on...

Added reply in a thread stock shim sequence 93' CR125 3/12/2017 9:44 AM

I made a wooden clamp to put it in the vise. The cartridge kept rotating a bit, but I hit the wrench instead of pulling it. That caused enough impact to loosen the thread after heating. Don't you just need to heat more and try it that way?

Added reply in a thread stock shim sequence 93' CR125 3/12/2017 3:19 AM

Note that your flow is not 33% more. The diameter is, but the area increased much more.. pi * r 2 = 3,14 * 1 * 1 =3,14 square mm whereas 3,14 * 1,5 * 1,5 = 7 square mm. So the flow is more than doubled. What is the reason for that 17x0,15 shim, anyone ... more »

Added reply in a thread stock shim sequence 93' CR125 3/12/2017 3:11 AM

I'll show the picture of that drilling here.

I needed to take this off to place the spacer, but you won't. However the same counts for the cartridge: At the place where you're drilling, the diameter of the inner part is actually smaller than ... more »
Added reply in a thread stock shim sequence 93' CR125 3/7/2017 2:19 PM

Yeah just open it. I have another threat about this topic, in which I'll show what slipdog means. When you're drilling the tube and watch closely, you can see when you're through. Loctite was applied to my threat, so a couple seconds heating was required ... more »

Added reply in a thread stock shim sequence 93' CR125 3/6/2017 12:44 PM

Actually this translation is incomplete. In the Dutch version it says: Compression damping (Right leg, top adjuster) >affects entire stroke Turn open when the fork feels harsh at short hard bumps Compression damping (Right leg, bottom adjuster) >affects ... more »

Added reply in a thread stock shim sequence 93' CR125 3/6/2017 10:28 AM

Damn, it appears to be a mod done by a suspension tuner to make it more adjustable. See image. Unfortunately they didn't have time to look into it at the moment, so let's continue the research

sad
Interesting though. ... more »
Added reply in a thread stock shim sequence 93' CR125 3/4/2017 4:37 PM

Thanks. Althoug I have to watch The European eBay

smile
Slipdog are you still confident that the shim stack you provided will be fine if I swap the flute with an original one? I bought the missing shims and made that stack
Added reply in a thread 1988 CR250 clutch question 3/4/2017 3:44 PM

Seems we've sorted this entirely now! Will try a call to some brands anyways later.

Added reply in a thread stock shim sequence 93' CR125 3/4/2017 3:32 PM

Mmm, ok, but what does it comprehense technically ? Would better have bought a newer model fork instead of this complete overhaul then. Because it will be hard to find that cartridge as a single part. Must have been someone smart, one wouldn't destroy ... more »

Added reply in a thread 1988 CR250 clutch question 3/4/2017 12:37 PM

Damn true. When googling the number you'll land onto crf pages! I'll try to call a brand to see if they confirm

Added reply in a thread 1988 CR250 clutch question 3/4/2017 12:02 PM

That's correct. I have an 88 engine with later alloy water pump housing and then The 90-91 clutch fits. But what is The difference with clutches of 92 and later?

Added reply in a thread stock shim sequence 93' CR125 3/4/2017 11:44 AM

Or might this be the reason that left and right are valved differently? Just finished making them equal. Now start to assembly everything again.

Added reply in a thread 1988 CR250 clutch question 3/4/2017 9:21 AM

Do the clutch baskets after 91 also fit? Aftermarket clutches go up to 91 and then from 92 to 2000 somewhere. What's the difference? Good to know, because there's much more available for these years...

Added reply in a thread 96 CR250 with Oversized tank photo post! 2/6/2017 11:06 PM

So do you think the picture is larger than the ims 3.2g?

Added reply in a thread 96 CR250 with Oversized tank photo post! 2/6/2017 11:03 PM

That's The onlu picture i found, don't even know The size and brand of that one. I have a 125cc, looks bulky quite fast

Added reply in a thread 96 CR250 with Oversized tank photo post! 2/6/2017 12:55 PM

Is the 3.2gallon model like this one or less bulky?

Added reply in a thread 96 CR250 with Oversized tank photo post! 2/6/2017 12:39 PM

Would like to see a picture too. No one has?

Added reply in a thread stock shim sequence 93' CR125 2/6/2017 9:46 AM

Slipdog thanks a lot!!!. I'll try to get the missing shims and reassemble it. Will post it for later usage by others. Also the shortening. That came out nicely. Thanks once again.

Added reply in a thread stock shim sequence 93' CR125 2/5/2017 3:03 PM

It's midnight where I live. I still be awake for a while, but if more convenient for you we'll continue tomorrow

smile
If better I can make identical base plates on a lathe.