GB 911's Forum Activity

Reply to Weirdest mechanical failure or problem 5/21/2020 8:02 AM

Me and my buddy where riding in Austria. Guy next to us couldn’t start his bike. First we let him mess around but soon we start feeling sorry for him and we start helping him. Bike sounded like it was flooded. He had no spark plug with him but we had. ... more »

Reply to Kx 250 1991 transmission 5/10/2020 11:07 PM

Try vd Vegt they are located in Dalfsen in the Netherlands, close to the German boarder.

Reply to 2018 Demo bike = Sweet deal? 4/23/2020 10:05 PM

Congratulations on your new bike! Since this is your first new bike here are some tips. From the factory there often isn’t much grease in the steeringhead, pro-link and swingarm bearings. Re grease them. After a few hours check the bolds / nuts and spokes. ... more »

Reply to 1998 KX250 Build 4/3/2020 12:12 PM

I bought it from Dirk Timmer.

Reply to What to check when viewing used bike ? 1/18/2020 3:17 PM

1e If you have the chance, run the VIN to check if the bike is not reported stolen. 2e check if the cases have no repairs on them. 3e check underside of the frame for flat spots. 4e check swingarm, look if the chain has not been worn through the chainslider ... more »

Reply to 1995 CR250 - Done 1/6/2020 10:29 PM

No I didn’t do anything Other than degrees them. I checked the threads and heads of every bold and made a list of all the oem Bolt specs for my bike. Every worn, damaged or incorrect piece was replaced.

Reply to 1995 CR250 - Done 1/4/2020 10:06 AM

Yes it was €65 for the lot. Here are some pictures...

... more »
Reply to 1995 CR250 - Done 1/3/2020 10:58 PM

Hello Brain, first let me say I like your build. It’s good to see a bike brought back to life. On the shock ring, get it replated along with all the other hardware. (Axels, springs and al steal nuts and bolds. I even did my spokes and nippels) it really ... more »

Reply to 99-02 kx125 rear wheel offset help 7/3/2019 10:45 PM

Front 1.60 rear 2.15 (my measurements where in cm)

Reply to 99-02 kx125 rear wheel offset help 7/3/2019 2:20 PM

Reply to 99-02 kx125 rear wheel offset help 7/3/2019 2:19 PM

This is measured from the disk side on my 1998 KX250. Front and rear wheels are there same measurements. I hope this helps you in any way.
Reply to 1998 KX250 Build 6/1/2019 11:07 AM

Try Dirk Timmer. That’s where I bought it.

Reply to 1998 KX250 Build 6/1/2019 11:04 AM

... more »
Reply to 1997 Kx250 inquiries 2/9/2019 11:09 AM

That’s to bad! A nice bike is getting hard to find.

Reply to 1997 Kx250 inquiries 2/8/2019 3:07 PM

Some before and after photos of my 1998 KX250

Reply to 1997 Kx250 inquiries 2/8/2019 3:06 PM

Reply to 1997 Kx250 inquiries 2/8/2019 12:54 PM

Thats a Nice find! With my build i went for the original look. I hope you find a good bike to start the project with.

Reply to 1997 Kx250 inquiries 2/7/2019 12:10 PM

Powervalve And transmission parts are NLA. I recently build a 1998 KX250 and found those where the difficult to get parts.

Reply to Kawasaki KX 125 1996 GP 1998 Tortelli JdG Replica 7/5/2018 10:38 PM

Nicely done! Great that you bought it new and still have it!

Reply to YOUR best corner photo 7/5/2018 10:24 PM

(Credit for the photo to Hans)