Added reply in a thread Tom Morgan vs Tokyomods for engine mods 9/21/2022 8:40 AM

Thanks for the reply. I actually just sent it out to Tokyomods. I’ll get to try both companies out. I’m building two of these and Tom did the first engine.

Added reply in a thread Steering Stem Bearing Replacement 9/18/2022 7:50 PM

I had a hard time tonight getting the races in with the OEM race install tool. I couldn’t get the races to go in straight. Ended up using a hammer on the the race tool to seat them flush.

Added reply in a thread 2007 Honda CRF 250R 9/18/2022 6:37 PM

Thanks man! It’s taken awhile to find some parts and then a few months to get the coatings and suspension done. Knee replacement in April didn’t help either. Should be pretty good when I finally finish!

Added reply in a thread 2007 Honda CRF 250R 9/18/2022 3:26 PM

Starting back at it. Picked up the frame and suspension this weekend. Didn’t get much time to start putting it together because of the hurricane in Puerto Rico.

... more »
Added reply in a thread I Already miss AMA Motocross! 9/12/2022 5:26 PM

I miss Supercross more. Motocross just has such crappy coverage unless you can make it in person to a race. I had to miss Budds Creek this year due to knee replacement and not being able to walk around much. Atlanta SX was a blast to go see.

Added reply in a thread MX companies I should support. 9/10/2022 1:32 PM

TAGMX-very good at communicating, I'm currently getting suspension work done, Cerakoting and powder coating done by them. Also had them look over an engine I built to make sure I didn't mess anything up. Rocket Exhaust-Seem a lot better now with new ... more »

Added reply in a thread Tom Morgan vs Tokyomods for engine mods 9/7/2022 9:33 PM

Is TZR Tom Zont Racing? I hadn’t heard of them before. When I first searched, I think I typed TRZ and it came up as a place in Germany. Lol

Added reply in a thread Corporate sponsors. HELP !!!! 9/5/2022 6:24 PM

Let the riders and teams worry about it maybe? Not sure why fans need to help try and find ways to fund a sport.

Added reply in a thread Tom Morgan vs Tokyomods for engine mods 9/1/2022 9:36 PM

... more »
Started new thread Tom Morgan vs Tokyomods for engine mods 9/1/2022 9:31 PM

So, I’m doing my mid-life crisis bike builds, two 2007 CRF 250r’s. One engine is built, working on the second. Tom is 4-5 months out, Tokyomods is faster. I had Tom do the porting, case boring on the first engine. I sent both carbs to Tokyomods. Looking ... more »

This forum thread has 9 replies

Added reply in a thread WTB RG3 clamp set/bar mounts and engine hangers for '07 CRF 250R 8/23/2022 12:11 PM

I’m interested in some pictures of the red clamp and bar mounts. Thanks!

Started new thread WTB RG3 clamp set/bar mounts and engine hangers for '07 CRF 250R 8/22/2022 5:18 PM

Looking to buy another set of RG3 clamps top and bottom with bar mounts and a set of engine hangers for a 2007 Honda CRF 250R. Prefer RG3 red clamps, but open to other colors and brands.

This forum thread has 5 replies

Added reply in a thread Hot start valve broke off in carb 8/21/2022 5:37 PM

I didn’t think about air, I used that method disassembling the brake calipers to remove the brake pistons.

Added reply in a thread Hot start valve broke off in carb 8/21/2022 5:35 PM

Thanks for the tips guys! I have one of those metal dental picks, but can’t get it to pop out. I figured it’s gummed up or corrosion. I’m building two of these bikes, the other bike wasn’t an issue removing it. This carb has sat for a couple of years ... more »

Started new thread Hot start valve broke off in carb 8/21/2022 12:41 PM

I was prepping a carb to send to Tokyomods and was having trouble removing the hot start cable and ended up breaking it off inside the carb. Any recommendations how to remove it? I can spin it with a screw driver, just can’t get it out. Currently soaking

... more »

This forum thread has 5 replies

Added a comment about feature Jeremy McGrath Replica 2000 YZ250 | Tyler Winstead's Bike Build - Why That Bike? 8/11/2022 6:18 PM
Electro21

This is an awesome feature, I dig hearing the story, similar to my build I have going on, other than getting free parts and finding factory stuff! Hopefully this sticks on a weekly or monthly basis.

This feature has 5 comments.

Added reply in a thread ISO RG3 second gen 1 1/8 bar mounts 8/10/2022 6:13 PM

Bummer, wish you had a complete set for 2007 CRF.

Added reply in a thread ISO RG3 second gen 1 1/8 bar mounts 8/8/2022 3:14 PM

Any of those clamps to fit a 2007 CRF 250R? Looking for a set for my next build, color doesn’t matter as much as condition. Prefer oversized mounts.

Added reply in a thread Twisted engineering bars 4x 8/7/2022 11:46 PM

Why are they so expensive? I've never heard of them, so I checked out the website. I couldn't read the first three lines in the description because of the poor website design. $459 for handlebars seems pricey to me, just curious since I don't know anything ... more »

Added reply in a thread ISO RG3 second gen 1 1/8 bar mounts 8/7/2022 11:33 PM

I hope you can find them! I spent over a year trying to find a full set of RG3 clamps for my 2007 CRF 250R build. I was able to locate a new set and was about to get a set from Ride Engineering. I tried contacting RG3 for leftovers, and they replied

... more »