Started new thread 2016-2018 Tc 125 (sx125) factory BigBore 150 kit. Husqvarna/KTM 7/24/2019 1:09 PM

I have a 2018 Tc 125 converted SM. See my bike check for specs 🤟🏽 Today I ordered a 150 kit because I noticed a lean spike in my rpm when I drained/ran the carb dry the bike redlined to 15,030. it was consistently getting 14,400 Before that and now it ... more »

This forum thread has 1 reply

Added reply in a thread 17 TC 125 cutting out 7/14/2019 8:15 AM

For sure bro, I’ll let you know on here! 🤟🏽

Added reply in a thread 2007 CR250 Stator ohm specs 7/12/2019 1:42 PM

You bet bro, subscribe to his channel!

Added reply in a thread Time Sert for 2015 Ktm 125 sx - Question/help 7/11/2019 9:04 PM

Take off the clutch case and Just retap the threads of the drain

Added reply in a thread 2007 CR250 Stator ohm specs 7/11/2019 8:41 PM

https://youtu.be/P2jxB49krIE 9:00 mark 😎 1.7 ohm btw still check out my boys YT channel he’s one of the best!

Added reply in a thread Suzuki rm 125 power valve help 7/11/2019 8:29 PM

😳 i hope you weren’t yawrning on it hard because you are supposed to use a special tool to lock the PV arm in place when removing that bolt Same when reinstalling.

Added reply in a thread Carb float height Problems, change during ride ? 7/11/2019 8:18 PM

Also I forgot to say Iv pinched that o ring before it put a tiny flat spot making it leak all over as soon as I turned the gas on took all apart and replaced it with the other one I got put water proof grease on the oring and boom no leak.

Added reply in a thread Carb float height Problems, change during ride ? 7/11/2019 8:14 PM

Sounds like the o ring on the needle valve and was the gas left on?

Added reply in a thread 17 TC 125 cutting out 7/11/2019 8:00 PM

Switched to the kiehin, bike runs so good now had to turn the power valve all the way back out where it’s most fun, Nice kit from JD included well worth the switch for non head ache. Next thing to do is get the stic metering rod from what Iv read and ... more »

Added reply in a thread 17 TC 125 cutting out 7/5/2019 10:57 PM

Thought I’d keep y’all posted this is what I came up with🤷🏽‍♂️

Added reply in a thread 17 TC 125 cutting out 6/30/2019 7:03 PM

The spark plug ground electrode is white i gotta just make it as rich as can be and see what happens, current situation is had to cut the throttle cable to get the plastic retaining ring around from the aluminum screw in piece that goes into the slide ... more »

Added reply in a thread 17 TC 125 cutting out 6/24/2019 7:43 PM

Do you still run the sc2?

Added reply in a thread 17 TC 125 cutting out 6/24/2019 6:12 AM

Coming off WOT it seems to wanna bog out i notched the slide and it was better but still would wanna die I think I’m gonna try clip 3, then a 32.5

Added reply in a thread 17 TC 125 cutting out 6/23/2019 12:45 PM

I’m tryna upload a video to the page but it’s right around 1/8 1/4 throttle pilot 30 main 480 I think clip 1 and 1 1/2 turns out. I DIDNT notch the new #5 slide on the little U shape, could this be the reason I don’t remember anybody saying to notch ... more »

Added reply in a thread 17 TC 125 cutting out 6/23/2019 12:33 PM

Added reply in a thread 17 TC 125 cutting out 6/21/2019 9:36 PM

It Boggs 1/4 throttle and it had bogged in the top end after a short pull not even topped out imm gonna post a video tomorrow see what y’all think if it keeps on running like trash I’m going to get the sc2 smart carb ASAP

Added reply in a thread 17 TC 125 cutting out 6/21/2019 9:07 PM

Changed the jet block gasket with a jd kit also go a genuine #5 slide, 42-74 Needle clip 1 and a s-4 needle jet, 1.5 aso 470main 30 pilot is what I put it in the garage with. Ran clip 2 ran 480main and 32.5 pilot. no good, I didn’t do a compression test ... more »

Added reply in a thread 17 TC 125 cutting out 6/21/2019 6:58 PM

Added reply in a thread 17 TC 125 cutting out 6/18/2019 4:26 PM

So this just happened lol.
Added reply in a thread 17 TC 125 cutting out 6/15/2019 2:44 PM

Is this the part you cut down? I only ran a file through the notch on my slide that’s it