Added reply in a thread Vforce 4R or Boyeson Rad / KTM/Husky 250 10/17/2019 6:11 PM

Was basically my same thought. I went with the Rad.

Started new thread Looking for OEM Husky ODI grip CAM! 10/17/2019 6:03 PM

I bought an 18 TC250 and the original owner swapped the grips to non-lock on grips. I ordered new ODI lock-ons imagining it would come with an replacement for the OEM cam that comes on the grip. However, ODI has informed me that they are not allowed ... more »

This forum thread has 8 replies

Started new thread Vforce 4R or Boyeson Rad / KTM/Husky 250 10/16/2019 8:20 PM

Just curious if anyone has tried either one of these in their 17-18 KTM or Husky 250 2T. I had Vforce 4R in my 17 KTM 250SX and just remember it being better throttle response and not much else. Has anyone tried the Boyeson in either bike? Had boyeson ... more »

This forum thread has 4 replies

Started new thread Neken SFS Triple Clamps Yamaha 6/8/2019 5:59 PM

Selling a set of 22mm offset Neken SFS clamps. Around 7 hours on them. Selling my bike so putting stock parts back on. As far as I can tell they fit 2014-2019 yz450F. Not sure how far back for 250F. They were mounted to both a 2019 YZ250F and YZ450F.

... more »

This forum thread has 2 replies

Added reply in a thread YZ250 engine issues 5/15/2018 9:41 AM

Yeah, what I was thinking for the blow-by issue

Added reply in a thread YZ250 engine issues 5/15/2018 9:09 AM

Honestly man, no idea. They dont appear very beat up, but that could obviously mean nothing. I do have another cylinder at home I got with another bike I could throw on, but I don't think it will solve the oil issue.

Started new thread YZ250 engine issues 5/15/2018 8:35 AM

Bike died at the track few weekends ago. Came out of a corner and just died. It did start up after but sounded awful, so I killed it and put in a new top end. Again, Bike started up, but still sounds bad, almost like a deep echo coming from in the engine.

... more »

This forum thread has 8 replies

Added reply in a thread yz250/250f triple clamps SSS conversion 3/5/2018 2:39 PM

... more »
Added reply in a thread yz250/250f triple clamps SSS conversion 3/5/2018 2:30 PM

Here's a picture of the bike if anyone cares. Would like to get a 22-23mm offset thrown on soon. Having a hard time fine tuning it for cornering. Thanks everyone for the help.
Added reply in a thread yz250/250f triple clamps SSS conversion 3/5/2018 1:32 PM

Not sure where the axle is from on the bike now, but it sticks out a tad on the right side as it is. So maybe with new clamps, that will become flush.

Added reply in a thread yz250/250f triple clamps SSS conversion 3/5/2018 5:38 AM

Just the guards in general or the bolt alignment? Pretty sure they're aftermarket because they're black. But I can when I can get home.

Added reply in a thread yz250/250f triple clamps SSS conversion 3/5/2018 5:37 AM

Sorry man, looking for different offset.

Added reply in a thread yz250/250f triple clamps SSS conversion 3/5/2018 4:25 AM

Stock? Looking to change the offset.

Started new thread yz250/250f triple clamps SSS conversion 3/4/2018 7:30 PM

Ok, so I have an 05 yz250. It has SSS fork conversion which appear to be from anywhere from 2008-2014 (Guy I bought it from somehow doesn't know). I say this because it has the smaller diameter axle holes and they have the black bands on the bottom of ... more »

This forum thread has 18 replies