Added reply in a thread Swingarm Finish 3/26/2018 8:16 PM

I just did my swing arm. It's on a kx with factory paint. I DA sanded mine and boy what a pain. I took it to 220 then hit it with a gray scuff pad. A finger nail will mark it.

Added reply in a thread 06 KX250 It's Done!!!! 3/26/2018 9:01 AM

Thanks... It's an outlaw racing stainless brake line. The fittings are pretty nice on it.

Added reply in a thread 06 KX250 It's Done!!!! 3/26/2018 7:11 AM

They look way better in sunlight. Maybe tomorrow I'll be able to roll it out and get a good picture of them.

Added reply in a thread 06 KX250 It's Done!!!! 3/25/2018 7:25 PM

... more »
Added reply in a thread KX 125 Build 3/25/2018 5:39 PM

Use some epoxy for the rubber parts. I just put some on and it holds nicely

Started new thread 06 KX250 Stator Plug WTB 3/23/2018 11:14 AM

I'm looking for a 06 kx250 Stator that is junk. I smashed the plug and can't find a replacement. If anyone has one that they would be willing to sell let me know. Thanks

This forum thread has 1 reply

Added reply in a thread 06 KX250 It's Done!!!! 3/19/2018 8:07 PM

It's not dead on but it's close to kx green
Added reply in a thread Parts washer solvent? 3/18/2018 1:14 PM

Been using diesel also. I'm not using it all the time and it's well ventilated so the fumes aren't bad. Works pretty good

Added reply in a thread 06 KX250 It's Done!!!! 3/16/2018 6:31 PM

... more »
Added reply in a thread When a national level pro blasts past you, you think? 3/15/2018 4:43 PM

About 5 years ago here in New Mexico Jason Anderson blew past me in a corner and scrubbed a 70ft table only a few feet off the ground. It was pretty sick.

Added reply in a thread 2002 Kx 125 Rebuild 3/11/2018 8:34 PM

Nice. What kind of finish is that?

Added reply in a thread 96-97 YZ Navy Blue Plastics. Anyone Interested? 3/11/2018 3:39 PM

laughing
... more »
Added reply in a thread 06 KX250 It's Done!!!! 3/10/2018 4:20 PM

More progress being made. Removed casting marks from triple clamps then detailed them so they looked nice and pretty. What a pain that was. Blasted them after. Tomorrow I will take them off to get powder coated along with the ignition, clutch cover and

... more »
Added reply in a thread 06 KX250 It's Done!!!! 3/9/2018 4:16 PM

After hours of working on this swingarm I'm done with it

Added reply in a thread 06 KX250 It's Done!!!! 3/7/2018 4:33 PM

Added reply in a thread FC350 Engine Noise 3/6/2018 5:53 PM

It's either ride it and pay close attention to the noise in case it gets louder or tear into it. Not much else you can really do.

Added reply in a thread 06 KX250 It's Done!!!! 3/5/2018 4:06 PM

Added reply in a thread Turned down hub strength 3/5/2018 10:50 AM

So are you saying the ribs running length wise with the hub are from the casting process and have nothing to do with strength?

Added reply in a thread FC350 Engine Noise 3/4/2018 8:42 AM

Oh dang. Well I guess all you can do it ride it and keep an eye on the oil for any unusual deposits.