Started new thread GET ignition front fender LEDs 6/6/2021 10:12 AM

I have the GET ignition with the LEDs on the front fender for launch control. I’ve found I start better without the LC enabled, but it might be useful to use the front fender LED Christmas tree as a rev gauge. Is there any way I can enable it to do that

... more »

This forum thread has 2 replies

Added reply in a thread Interesting 3-D printing nugget re KTM MotoGP 6/2/2021 5:49 PM

Ah I get it! Fresh Top End - v clever. Good on ya fella! Cheers Simon EDIT - I'm probably about 10 years late here.

Added reply in a thread Litpro vs crossbox 5/20/2021 8:52 AM

I've just discovered Crossbox after I lost my LITPro last week and haven't been able to buy a replacement LITPro that does everything I want (overlaying laps, accel/decel analysis, HR measurement and airtime analytics. It looks like Crossbox is also ... more »

Added reply in a thread RXR R-Pro chest protector neck brace compatibility/general questions 5/19/2021 9:19 PM

On top of the RXR on the back and below the RXR on the front - the brace hooks under the front of the RXR.

Added reply in a thread LITPro 5/19/2021 10:32 AM

Thanks, really useful. Looking at the compatibility table, if I want a device that does all the features of my old LITPro device (including HR and airtime data) I need an HDGPS, but they don’t seem to sell an HDGPS unit on their website and I can’t see ... more »

Started new thread LITPro 5/18/2021 3:25 PM

I lost my original LITPro and went to their website to see how much a replacement was gonna be and they no longer sell it (website says it's been discontinued). It looks like the GPS box they're selling (the brick-like XGPR160) doesn't do airtime data ... more »

This forum thread has 8 replies

Started new thread WANTED - Original LITPro 5/18/2021 3:21 PM

I lost my original LITPro and it looks like it's been discontinued, so I'm looking to buy one if anyone has one they'd like to sell. Cheers Simon

This forum thread has 2 replies

Added reply in a thread RXR R-Pro chest protector neck brace compatibility/general questions 5/18/2021 1:28 PM

I have the RXR R-Pro and the new Atlas Air brace and they fit together well. It helps, generally, with neck braces that I have a long neck (I'm 6'1") - if my neck was shorter I wouldn't wear a neck brace as it would restrict my movement on the bike.

... more »
Added reply in a thread Found this while doing an oil change... 5/16/2021 4:28 PM

Absolutely!

Added reply in a thread Found this while doing an oil change... 5/16/2021 4:27 PM

Thanks Kevin. I agree, but I have zero idea how an extra clutch pin could have got in there unless it was dropped in during assembly at the factory and stayed put for almost 60 hrs and only then freed itself. Very odd.

Added reply in a thread Found this while doing an oil change... 5/16/2021 4:01 PM

Oil screen had some tiny, tiny metal particles, and I didn’t see any fragments in the oil filter.

Added reply in a thread Found this while doing an oil change... 5/16/2021 4:00 PM

Yeah it looks like a clutch pin, but unless they dropped in an extra one for me when the bike was assembled in the factory it isn’t one as I have accounted for them all. Could be a shift fork slider pin, not that I know what that is. Tear down will tell ... more »

Added reply in a thread Found this while doing an oil change... 5/16/2021 3:58 PM

Gears are all good. I know this because I ran the bike on the stand thru all the gears to warm up the oil before doing the oil change.

Added reply in a thread Found this while doing an oil change... 5/16/2021 2:00 PM

Given the potential consequences of me norsing it up, I will not be going anywhere near it :-)

Added reply in a thread Found this while doing an oil change... 5/16/2021 8:41 AM

Not to my knowledge. Engine has run flawlessly for 60 hrs with the exception of the Rekluse EXP base plate failing, but it all held together and I replaced it.

Added reply in a thread Found this while doing an oil change... 5/16/2021 5:19 AM

Yeah I have 6 clutch pins with the OEM clutch I took out, and the 6 pins are still in the Rekluse in the bike.

Added reply in a thread Found this while doing an oil change... 5/16/2021 5:17 AM

I thought that but went back and looked at the drain plug and it’s intact with magnet still attached. Here it is with the piece that came out...

Added reply in a thread Found this while doing an oil change... 5/15/2021 6:08 PM

Wow, that’s odd. So you never worked out what part the metal pieces were from? Cos you would think if metal parts this big fall out of your engine that eventually something’s gotta give. If these metal pieces are not from an engine part then the only ... more »

Added reply in a thread Found this while doing an oil change... 5/15/2021 1:36 PM

It’s possible, but it must have been stuck somewhere for 50 hrs as it only showed itself on the 60 he oil change. Given what’s going on in there and the vibration etc I find that hard, but not impossible, to believe. In any event, the pieces I pulled ... more »

Added reply in a thread Found this while doing an oil change... 5/15/2021 1:33 PM

Yeah there are 12 in the OEM clutch but 6 in the Rekluse that I have installed.