Added reply in a thread Kawasaki Destination Charges 6/22/2019 11:07 AM

What law is that specifically? To the OP, most manufacturers lost the destination charge on their website and it varies by model. A side x side is usually double that of a bike as it costs more to ship (size, weight, etc.). Our dealership would normally ... more »

Added reply in a thread Spoke Skins should be banned!! 6/19/2019 11:53 AM

Different strokes for different folks, but cool thread idea.

Added reply in a thread Ever have one of those moto's ... 6/13/2019 3:04 PM

Added reply in a thread Fmf 4.1 Muffler hex screws. 6/13/2019 3:00 PM

Take the good one out and head to Ace hardware if you're in a pinch and trying to ride this weekend. Match the depth, pitch and pick up some new ones for about $1. Call FMF and get a new set in the meantime and swap them out when they're delivered in ... more »

Added reply in a thread Full exhaust system calibration 6/11/2019 9:00 AM

Agreed, best option is a dyno tune. That goes for your street bike as well, especially if your running a power commander.

Added reply in a thread 2012 rmz250 6/5/2019 11:24 PM

Pull the head, should give you more answers than we can at this point.

Added reply in a thread Keeping white gear from getting stained 6/3/2019 6:19 PM

You could have done that with basic laundry detergent. I'm guessing all those brown stains are almost as old as the jersey

laughing
Added reply in a thread Throttle tubes 6/3/2019 10:24 AM

I've always had great luck with the pro circuit tube. I've never ran the pro taper tube with bearings but have also heard good things. I clean/lube cables every 3 or 4 rides so I've always coated the bar with a light coat of grease, then a very small ... more »

Added reply in a thread My picks for the ten best-looking stock KTM MX bikes of all time. 5/29/2019 3:33 PM

Added reply in a thread 19 YZ250 jetting help needed please. 5/27/2019 2:15 PM

50:1!!!!? Yamaha even put a big fat eyesore of a sticker on the fender that says 32:1 for you.

Added reply in a thread Aluminum frame purpose? 5/7/2019 11:56 AM

Do you know how hard it is for me to convince executives to decrease profits and increase production costs? No wonder it's been a bad quarter.

Added reply in a thread Aluminum frame purpose? 5/7/2019 11:40 AM

Increasing profits while decreasing production costs. This is the target in any product development process.

Added reply in a thread Aluminum frame purpose? 5/7/2019 11:38 AM

A customer is not entitled to a manufacturers design/manufacturing costs. It was/is lighter, so it wasn't a scam at all.

Added reply in a thread Aluminum frame purpose? 5/7/2019 11:27 AM

I'll also add that KTM/Husky looks inside the engine for weight savings as well.

Added reply in a thread Yamaha app question (total hours) 4/29/2019 11:51 AM

Any Yamaha dealer can plug it in and pull up the total hours. You might be able to find a local private shop with the tuner as well. But again, any yamaha dealer should have this. Takes 2 minutes to plug it in and pull up the info.

Added reply in a thread Yamaha app question (total hours) 4/29/2019 11:11 AM

Can they be manipulated? Sure they can. Is the average Joe capable of manipulating the app to save a few hours? More than likely not. I would say there's a 99.9% chance those hours are correct. It goes to the old saying that anything can be done with ... more »

Added reply in a thread Crappy picture on tv for races 4/16/2019 11:00 AM

I think this has more to do with SX not being broadcast in 4k. There are tons of true 4k televisions out. Not all channels will broadcast in 4k yet though. Kind of how it took a little while for networks to jump on the 1080 bandwagon. However, the true ... more »

Added reply in a thread Crappy picture on tv for races 4/16/2019 10:47 AM

To be fair, they waste a lot of the screen with the scoring and timing on the left of the screen. We miss out on wide angle shots because of this. Off topic, but my best friend works in the production industry and their company has done SX a few years ... more »

Added reply in a thread Crappy picture on tv for races 4/16/2019 10:06 AM

Good point, 120hz is a MUST

Added reply in a thread Crappy picture on tv for races 4/16/2019 9:44 AM

Ah, that's definitely not the HDMI cable then. What cable service do you have? Might be worth a call or email to your provider.