Added reply in a thread De-rednecking this 2003 rm 250 10/10/2019 4:42 PM

It's perpus, made you do it , awnperpus Gititrite

Added reply in a thread De-rednecking this 2003 rm 250 10/8/2019 11:57 AM

Lol, other than the excessive amount of Grease that would be pumped into the head tube in order to even reach the bearings hahahahahah, sure would make a mess when it comes time to replace the bearings or even to remove the triple clamps :/

Added reply in a thread De-rednecking this 2003 rm 250 10/7/2019 4:37 PM

I bought a 2008 rm250 off a friend of mine, I shouldn't have trusted him, he said it was "mint" and he just "rebuilt it", well...... I had to rebuild his rebuild, and he even installed the front brake master seals in backwards and made an effective brake ... more »

Added reply in a thread 2003 CR250 Diamond in the Rough (Phase 1 DONE) PIC HEAVY 9/4/2019 10:55 AM

I think your going to notice right away the difference in feel between the stock cr vs the crf forks, I felt it took away some of the floppy feel when switching directions, and the top heaviness of the bike was greatly reduced, and it allowed the bike

... more »
Added reply in a thread 2015 SX250/TC250 Suggested Mods 8/24/2019 9:20 AM

Well, it's been a while, sorry for the delayed response, busy with my house build, and work, and completely forgot about this. That's great news your stoked with how it's performing, Iv been putting in time getting my jetting sorted out, but haven't ... more »

Added reply in a thread 2003 CR250 Diamond in the Rough (Phase 1 DONE) PIC HEAVY 8/17/2019 10:52 AM

The whole carb debate is funny to me, at least you get it, the cheap route would be just to send your mikuni to dicks and have him put a intellijet in it, that will be give you the biggest net gains between the lectron and the mikuni. I am planning on ... more »

Added reply in a thread 2003 CR250 Diamond in the Rough (Phase 1 DONE) PIC HEAVY 8/12/2019 6:00 PM

Well, Iv owned the 08 144sx since 09, and Iv rebuilt the engine entirely twice now, last crank that was in it was a hot rods crank, and if it didn't punch out over 300hrs I'd be curious to see what it actually was, cuz I houred it out for years reliably,

... more »
Added reply in a thread 2003 CR250 Diamond in the Rough (Phase 1 DONE) PIC HEAVY 8/12/2019 8:24 AM

As well to be honest, i would really appreciate to see some pics of your cr125 as well, i an a huuuuuge smallbore fan, I may have owned more big bores than smallbores, but Iv held onto my 08 144 since 09, and only just recently rebuilt the engine, for ... more »

Added reply in a thread 2003 CR250 Diamond in the Rough (Phase 1 DONE) PIC HEAVY 8/12/2019 7:57 AM

Mr.Bradshaw, love that video, it's sooo good, and his other video of him on a 97 cr125 is pretty darn awesome as well.

Added reply in a thread 2003 CR250 Diamond in the Rough (Phase 1 DONE) PIC HEAVY 8/11/2019 8:55 AM

Probably one of the best bang for buck bikes out there, such a bad reputation surrounds them from all the mxa stigma everybody believed, Honda produced a 4 stroke powerband in a 2 stroke, and the world shunned it for not being "2 strokey" it's silly,

... more »
Added reply in a thread 2003 CR250 Diamond in the Rough (Phase 1 DONE) PIC HEAVY 8/4/2019 8:07 AM

Lordy, it's almost too clean to take out, but that's a silly thing to say really lol. Preeeeettyy jelly over that thing, nothing whips like that gen cr250r and just the ability to do whatever you tell it to do, and even on turn in mine would just let ... more »

Added reply in a thread Help Jetting my 2015 250SX Please!! 7/10/2019 8:30 AM

Have you replaced the stock Reed block in it? The stock block is a horrible design. If you haven't replaced the stock reed block, don't mess with jetting just yet, reed blocks in these bikes are a severe problem, I bought a 2014 ktm Reed block, to try ... more »

Added reply in a thread Suzuki rm 125 porting 6/17/2019 7:21 PM

I have to agree, rm125's haven't ever really Been notorious for bottom end delivery, I will say my 99 was an acception, I bet that engine would blow the doors off a new yz125, it was impressive, it had a way better mapping setup though, pwk longbody, ... more »

Added reply in a thread 2003 cr250r rc valve problem 6/16/2019 8:14 AM

That's pretty neat, never knew Honda did a servo motor butterfly valve in their exhaust piping, and super cool they reused the winding in other applications. All this Info is duely noted, as Iv stayed away from these bikes due to this issue, mechanical ... more »

Added reply in a thread It's a PREEEEEEEEEMIX thread 6/15/2019 8:41 AM

I have seen these twisted barrel carbs before, and looked really interesting for sure. I usually put Singh grooves in my heads, and the change in tone is very destinct, every bike Iv ever done it with has always had improved sound and throttle response,

... more »
Added reply in a thread Lighter Tires/Tubes? 6/11/2019 10:27 AM

I want me one of them Hoosiers, my 32f just started to tear a few side knobs, and I like what the review and weight have to say aboot them, cuz I agree with what the review said aboot the 32f, that tire was bomb at almost bars to the ground grip levels,and ... more »

Added reply in a thread 98 cr250 runs good under 75 degrees but won't run good over 80 6/11/2019 9:34 AM

That's a big drop in main jet sizes, for something that just started. That's weird.

Added reply in a thread It's a PREEEEEEEEEMIX thread 6/8/2019 1:57 PM

I have heard many people run avgas, with completely mixed reviews, and a few of the people Iv heard them from are guys i know and ride with, and they say to stay away from it all costs, but just due to their firsthand experiences with it, I took their ... more »

Added reply in a thread Suzuki rm 125 porting 6/8/2019 1:30 PM

Raising port heights up wil increase peak hp and peak torque numbers, but also move those peak numbers higher in the rpm range, but may start to hinder low end performance if taken past a certain degree, and rm125's in my opinion, haven't ever struggled ... more »

Added reply in a thread Lighter Tires/Tubes? 6/8/2019 9:53 AM

I paid 109.00 northern pesos taxes in for my mx33, and I saw the Hoosier rubber review, and they look to be more closer to the Dunlop 32f/3s tires the 33's replaced, so I can see how they would be a good performer, my only real complain with the 32f/3s

... more »