rob.boucher.547's Forum Activity

Reply to Vintage Motocross Mags 1970-2000 11/10/2017 11:53 AM

I also have hundreds of MXA,Dirt Bike modern cycle, popular cycling, all for sale special collections of models available 1976-78 RM's i have all the test issues! usa sales only- paypal fine!

... more »
Reply to looking to buy Dirt Bike magazine April 1978 and Motocross Action magazine august 1978 10/7/2017 7:03 AM

Sorry have been sold Sold all the 1978/79 issues as a lot

Reply to looking to buy Dirt Bike magazine April 1978 and Motocross Action magazine august 1978 10/6/2017 7:16 AM

I do not have the august must have sold that one I have over 200 issues 73-87 I am currently selling issues on facebook

Reply to looking to buy Dirt Bike magazine April 1978 and Motocross Action magazine august 1978 10/5/2017 5:54 PM

i have the april 17.00 plus 3:50 shipping usa looking for the other

Reply to Anyone has a Suzuki RM80C 1978 for sale? 9/27/2017 9:52 AM

Looking also if you have one in MN, Iowa,WI, upper midwest $$$$ paid

Reply to 1978 YZ80E hop up parts wanted 8/11/2017 9:38 AM

FMF

Reply to 1978 YZ80E hop up parts wanted 8/11/2017 9:36 AM

No, I did not make any 1977 silencers , I sold about 10 complete FMF pipe silencer combo's for the 76/77 YZ 80's $350.00 i will sell you one

Reply to Any Clue In Value of Fox Mud Guards 8/11/2017 7:18 AM

Sold mine for $300.00 a while back were new in package, sold my air shock gauge set 150.00 one new in package 1977 hat 350.00 i have a few items left, all will be sold in the next year

Reply to Vintage styled new bike 6/19/2017 9:41 AM

Reply to Vintage styled new bike 6/19/2017 9:35 AM

My retro YZ[j]https://p.vitalmx.com/photos/forums/2017/06/19/201030/s1200_image.jpg[/img]

Reply to Case repair opinions 5/25/2017 11:44 AM

Your seal bore stub shaft( spud) could have a flange and two allen bolts, and a key to mount right to mill table I had a set of RM465 cases, that had a destroyed set of swingarm pivot bore sleeves they are cast into the case set the same way I bored ... more »

Reply to Case repair opinions 5/25/2017 10:20 AM

When you remove the cast in sleeve you do not need to remove any parent material from the case, or maybe only .01 to clean up the cast in sleeve you are trying to remove should have a 2-3 mm wall per side your sleeve would have to be custom machined ... more »

Reply to Case repair opinions 5/25/2017 9:52 AM

set it up in a mill and bore it out( cut it out) How come your local shop would not do it?

Reply to Case repair opinions 5/23/2017 2:33 PM

Also, if you can leave the case in the mill and use the quill to press in the sleeve, and also recheck all your postions and sufaces to make sure your case has not moved

Reply to Case repair opinions 5/23/2017 1:06 PM

It is a easy no weld repair, using your seal bore for location make a spud to fit seal bore attach it to a flat steel plate sweep in od of spud install case half clamp and true case surface to plate/ perpendicular to quill/ boring head bore out old case ... more »

Reply to 1981 rm 250 slow build thread...completed.. 5/3/2017 11:52 AM

Build yourself a skid pan, and weld on frame tabs, they are worth

Reply to 93 CR 250 is the headshake that bad? 5/3/2017 11:48 AM

It happens most of the time , when you a slowing down on a choppy, or rutted surface. It is severe , but the engine is great on the 93-96 bikes

Reply to 1981 rm 250 slow build thread...completed.. 4/28/2017 7:21 AM

Use stock pistons if you can find one, wiseco 2 ring set up also Replace all the clips, ( kick idler gear, shaft clips) crank nut lock washer, clutch nut lock washer,screws,small shift springs, detent plungers, drain plug plungers, springs use the eibach ... more »