Added reply in a thread 1978 YZ80E hop up parts wanted 8/11/2017 9:38 AM

FMF

Added reply in a thread 1978 YZ80E hop up parts wanted 8/11/2017 9:36 AM

No, I did not make any 1977 silencers , I sold about 10 complete FMF pipe silencer combo's for the 76/77 YZ 80's $350.00 i will sell you one

Added reply in a thread Any Clue In Value of Fox Mud Guards 8/11/2017 7:18 AM

Sold mine for $300.00 a while back were new in package, sold my air shock gauge set 150.00 one new in package 1977 hat 350.00 i have a few items left, all will be sold in the next year

gamakona left a comment 8/9/2017 9:48 AM
C50_rm5_1445019165

I have a 1977 yz 80, did you make a muffler for that model year?

Added reply in a thread Vintage styled new bike 6/19/2017 9:41 AM

Added reply in a thread Vintage styled new bike 6/19/2017 9:35 AM

My retro YZ[j]http://p.vitalmx.com/photos/forums/2017/06/19/201030/s1200_image.jpg[/img]

Added reply in a thread Case repair opinions 5/25/2017 11:44 AM

Your seal bore stub shaft( spud) could have a flange and two allen bolts, and a key to mount right to mill table I had a set of RM465 cases, that had a destroyed set of swingarm pivot bore sleeves they are cast into the case set the same way I bored ... more »

Added reply in a thread Case repair opinions 5/25/2017 10:20 AM

When you remove the cast in sleeve you do not need to remove any parent material from the case, or maybe only .01 to clean up the cast in sleeve you are trying to remove should have a 2-3 mm wall per side your sleeve would have to be custom machined ... more »

Added reply in a thread Case repair opinions 5/25/2017 9:52 AM

set it up in a mill and bore it out( cut it out) How come your local shop would not do it?

Added reply in a thread Case repair opinions 5/23/2017 2:33 PM

Also, if you can leave the case in the mill and use the quill to press in the sleeve, and also recheck all your postions and sufaces to make sure your case has not moved

Added reply in a thread Case repair opinions 5/23/2017 1:06 PM

It is a easy no weld repair, using your seal bore for location make a spud to fit seal bore attach it to a flat steel plate sweep in od of spud install case half clamp and true case surface to plate/ perpendicular to quill/ boring head bore out old case ... more »

Added reply in a thread 1981 rm 250 slow build thread 5/3/2017 11:52 AM

Build yourself a skid pan, and weld on frame tabs, they are worth

Added reply in a thread 93 CR 250 is the headshake that bad? 5/3/2017 11:48 AM

It happens most of the time , when you a slowing down on a choppy, or rutted surface. It is severe , but the engine is great on the 93-96 bikes

Added reply in a thread 1981 rm 250 slow build thread 4/28/2017 7:21 AM

Use stock pistons if you can find one, wiseco 2 ring set up also Replace all the clips, ( kick idler gear, shaft clips) crank nut lock washer, clutch nut lock washer,screws,small shift springs, detent plungers, drain plug plungers, springs use the eibach ... more »

Added reply in a thread 1981 rm 250 slow build thread 4/18/2017 9:47 AM

Purchase a higher quality german bearing set, from your local bearing co. Or rework your crank journal flame spray plating weld and machine to size

Added reply in a thread vintage rolling art?? 4/18/2017 7:18 AM

Suzuki DR200 brake rod kits will fit all jap bikes with a brake rod (full size) $23.00 ?

Added reply in a thread 1981 rm 250 slow build thread 4/17/2017 11:46 AM

Check the diameter of your crankshaft( stator side) Suzuki cranks are generally undersize, for easy assembly most likely your play will not go away after new bearings, seals etc check how easy your new bearing fits on the crank end I think the 81 RM's ... more »

Added reply in a thread vintage rolling art?? 4/17/2017 10:00 AM

I have a few NOS FMF/PDI RM125 pipes 77/78 anyone interested$200.00 plus shipping

Added reply in a thread Diamond Don's Anyone? 4/12/2017 9:48 AM

will be there sat, sun

Added reply in a thread NOS FMF 1977/78 RM125, 78 RM100 4/2/2017 9:28 AM

Sorry, I have compared these to another pipe, I have (sold) these fit 1977/78 RM125 78 RM100 They are so close visually i did not know until i checked a few dimension's