Added reply in a thread another bar bend suggestion thread help! 1/6/2017 7:57 AM

If you want a little lower bar with less sweep try the TwinWall 921 bend. I ran them on my factory editions before I switched to the Mika Metal MC bend which is taller than the Renthal Mcgrath bend and has a bit less sweep too. I'm 6' tall and was looking ... more »

Added reply in a thread Looking for WP Cone Valve Forks 16 KTM SXF 1/6/2017 7:36 AM

I just shipped Powerband Racing a set of the 16 black cone valves and a 16 black trax shock that he's going to go through and sell. Call Billy at Powerband 763-241-2149

Added reply in a thread Wanted: FOX Instinct Used sz11 any color but black 1/6/2017 7:32 AM

I have a black pr and white pr both size 11 and brand new in the box here at the house. Selling for a buddy who broke his leg so bad that it basically forced him to retire. $350 each. Call or text 508 243 1232 or email me at mx29@charter.net. Thanks, ... more »

Added reply in a thread SOLD Please Delete 1/6/2017 7:25 AM

Those are the stock frame guards with my buddy from Squid Graphics grip guard grip tape on them. I ran the version on the frame only & was getting up to 10hrs out of them before they had to be replaced unlike the KTM powerparts ones that were lasting ... more »

Added reply in a thread Well here it is, the KTM SXF 450 Factory Edition 2016 1/5/2017 7:24 AM

My 16 FE450 was at .55 stock and it started ok but definitely had a stumble when whacking the throttle from an idle. I fiddled with the TPS setting as I did with my 15 FE450 and settled on .63/64 for both of them. They both started with basically just ... more »

Added reply in a thread For CR250#132 12/27/2016 4:15 PM

You guys are killing me!!

Added reply in a thread Nemx vs Nesc 12/27/2016 10:33 AM

I'm not sure that I'd label Pete as one of the toughest guys but I'd certainly say in my 30+ yrs of knowing and racing against him that he's without a doubt one of the nicest and most helpful guys that you'll ever meet. He's definitely one smartest and ... more »

Added reply in a thread For CR250#132 12/27/2016 10:15 AM

and..... I just spit my drink out!! :-)

Added reply in a thread WTB 2015.5+ Trax shock 12/23/2016 7:30 AM

I have a set of the new 16 black cone valves and trax shock here at my house that I'm going to clean up and list for a buddy in the next few days. Set up for 180lb expert MX.

Added reply in a thread Fox Instinct LE Boots 12/12/2016 8:01 AM

Same here, I was given a pr of the prototype Instincts in the spring of 12 and been wearing Instincts ever since. Most comfortable and best boot I've ever worn. Zero break in required. I've taken a new pr right from the box and raced that day with them. ... more »

Added reply in a thread Ktm 350 sxf 2016 fork pressures 12/3/2016 11:36 AM

No problem. I just wanted to let you know that me and everyone that I race with here in New England are running our AER's way softer than they're spec'd from KTM. The chart goes something like this 125/150SX 8.6 bar 250SX 10.2 bar 250SX-F 10.6 bar 350SX-F ... more »

Added reply in a thread Ktm 350 sxf 2016 fork pressures 12/3/2016 10:34 AM

Yes definitely. For what it's worth I only ran my AER's for the final 3 races of our season here in New England and I started at 148psi in them which is where they come stock and that I mentioned in my earlier post. I actually kept going down until the ... more »

Added reply in a thread 2017 ktm traction control switch 12/3/2016 10:26 AM

No, I don't think so because the 17's don't have the dial switch in the airbox like our 16s do.

Added reply in a thread Ktm 350 sxf 2016 fork pressures 12/3/2016 7:17 AM

You should be around 10.4 -10.6 bar.

Added reply in a thread 2017 Husqvarna FC450 - FINISHED 12/3/2016 5:51 AM

Those radiator caps are available on Mishimoto's site.

Added reply in a thread 2015 ktm 450 FE electrical help? 12/2/2016 7:01 AM

Definitely recheck the ground with an ohm meter. Also check the plug closely behind the front numberplate because I've seen 2 of them where a wire had pulled out of the plug and it was hardly noticeable but was causing the exact problem that you're describing. ... more »

Added reply in a thread Will KTM produce a 2017.5 FE? 11/26/2016 12:21 PM

There will absolutely be a 17.5 FE and it will be out sooner than you think :-)

Added reply in a thread Cone valve question 11/26/2016 8:33 AM

No problem and good luck. You're going to love the forks.

Added reply in a thread Cone valve question 11/26/2016 7:55 AM

It's a very thin 34mm wrench.

Added reply in a thread 2017 Husqvarna FC450 - FINISHED 11/26/2016 6:44 AM

Love the new stadium plate and the KTM fender on it. Much cleaner looking. I'm definitely getting that new plate for my new FE because my clamps were rittled with roost marks from this season. I had 98 Ti bolts and Think seat foam, full Ti FMF system ... more »